HP ZBook Power 15.6 inch G10 screw size

HP ZBook Power 15.6 inch G10 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. A screw that is even 1 mm too long in a laptop base can push into the keyboard, battery or a board trace, so match the length position by position.
2. Diameter: across the threads an M1.2 screw measures about 1.2 mm with calipers (usually a hair under). This device also uses M2 / M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.25 mm from one thread crest to the next (40 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 2–5 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source names a Phillips drive. For comparison, standard M1.2 heads take PH000 / JIS 00 (Phillips) or T1–T2 (Torx).
7. Tightening: no device-specific torque is published in these records. The site's general figure for M1.2 is about 5-8 N·cm into metal threads and 3-5 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with HP ZBook Power 15.6 inch G10, closest length match first.

• HP EliteBook 8460w also M2 × 4 mm
• Dell Inspiron XPS 9100 also M2.5 × 4 mm
• Dell Inspiron 14 5494 also M2 × 2 mm
• HP Pavilion x360 m1 Convertible PC u199 also M2 × 2 mm
• HP Mini 110 also M2 × 4 mm
• HP Pavilion dv2000 Entertainment also M2 × 2 mm
• HP Compaq N180 also M2.5 × 4 mm
• Lenovo ThinkPad T440 also M2 × 2 mm

Questions about HP ZBook Power 15.6 inch G10 screws

What size screw does HP ZBook Power 15.6 inch G10 use?

M1.2 × 2 mm for touchpad (qty 1, Phillips); M2 × 2 mm for hinge (qty 3, Phillips); M2 × 2 mm for speaker (qty 2, Phillips); M2 × 2 mm for touchpad (qty 5, Phillips); M2 × 2.5 mm for card reader (qty 4, Phillips); M2 × 2.5 mm for power button (qty 1, Phillips); M2 × 2.5 mm for SSD (qty 1, Phillips); M2 × 2.5 mm for system board (qty 3, Phillips); M2 × 4 mm for battery (qty 6, Phillips); M2 × 4 mm for bracket (qty 2, Phillips); M2 × 4 mm for fan (qty 3, Phillips); M2 × 4 mm for heat sink (qty 6, Phillips); M2 × 5 mm for battery (qty 2, Phillips); M2 × 5 mm for system board (qty 2, Phillips); M2 × 5 mm for unspecified (qty 1, Phillips); M2.5 × 4 mm for base cover (qty 2, Phillips); M2.5 × 5 mm .

How long are the screws in HP ZBook Power 15.6 inch G10?

The records range from 2 to 5 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M1.2 screw?

0.25 mm (coarse), which is the standard pitch for M1.2 machine screws. The tap drill is 0.95 mm and the normal clearance hole is 1.4 mm.

What screwdriver do I need for HP ZBook Power 15.6 inch G10?

The source lists a Phillips drive. Standard M1.2 heads otherwise take PH000 / JIS 00 (Phillips) or T1–T2 (Torx).

Can I use an imperial screw instead of M1.2?

No. Imperial look-alike: #0-80 UNF (1.52 mm) is the closest imperial screw, but it is bigger — not a substitute. Use a true M1.2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for HP ZBook Power 15.6 inch G10?

TechSpareWarehouse (our own store) lists M1.2 x 2mm, M2 x 2mm and M2 x 2.5mm, which match lengths in the records above.