item Roller Conveyor Aluminum Fastening Bracket D30 screw size
M6 · 14 mm long
Our records put item Roller Conveyor Aluminum Fastening Bracket D30 on M6 screws, 14 mm long.
It is listed for scope of delivery for the roller-conveyor fastening bracket explicitly lists 'Hexagon Socket Head Cap Screw DIN 6912 M6x14' along with a T-Slot Nut 8 St M6, used to fasten roller conveyor components to the T-slot profile frame.
Head and drive, as the source states them: socket cap head.
This entry is marked confirmed and comes from item24.com.
M6 means a 6 mm nominal diameter with a 1 mm thread pitch. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
item Roller Conveyor Aluminum Fastening Bracket D30 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 14 mm | 1 mm | Socket cap | not stated | Scope of delivery for the roller-conveyor fastening bracket explicitly lists 'Hexagon Socket Head Cap Screw DIN 6912 M6x14' along with a T-Slot Nut 8 St M6, used to fasten roller conveyor components to the T-slot profile frame | Confirmed |
Fitment records and sources
Scope of delivery for the roller-conveyor fastening bracket explicitly lists 'Hexagon Socket Head Cap Screw DIN 6912 M6x14' along with a T-Slot Nut 8 St M6, used to fasten roller conveyor components to the T-slot profile frame
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for socket cap screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The record states 14 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- 19-inch racks are not all metric: 10-32 and 12-24 UNC are still the norm in North America, with M6 the metric/square-hole cage-nut option.
- Manual explicitly warns that under-tightening this M6 hinge screw can let the door glass crash into the drum, so torque compliance matters more than just thread match.
More in Electronics, Racks & Enclosures
The same screw also fits
Devices whose records share a thread with item Roller Conveyor Aluminum Fastening Bracket D30, closest length match first.
- 19-inch server racks also M6 × 14 mm
- Rittal VX VX enclosure hinge countersunk Torx screw also M6 × 14 mm
- Ninebot Max G30 rear fender also M6 × 14 mm
- Xiaomi M365 / Ninebot brake caliper also M6 × 14 mm
- 19-inch rack cage nut and panel screw also M6 × 14 mm
- Wurth Elektronik WA-SSTIE steel spacer stud also M6 × 14 mm
- 48280AH lithium battery pack enclosure wheels also M6 × 14 mm
- 19-inch rack cage nut (metric square-hole rails) also M6 × 14 mm
Questions about item Roller Conveyor Aluminum Fastening Bracket D30 screws
- What size screw does item Roller Conveyor Aluminum Fastening Bracket D30 use?
- M6 × 14 mm for scope of delivery for the roller-conveyor fastening bracket explicitly lists 'Hexagon Socket Head Cap Screw DIN 6912 M6x14' along with a T-Slot Nut 8 St M6, used to fasten roller conveyor components to the T-slot profile frame.
- How long are the screws in item Roller Conveyor Aluminum Fastening Bracket D30?
- The record gives 14 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for item Roller Conveyor Aluminum Fastening Bracket D30?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.