Kenwood DPX-MP4070 car stereo ground/binding screw (accessory 4) screw size
M5 · 7 mm long
Our records put Kenwood DPX-MP4070 car stereo ground/binding screw (accessory 4) on M5 screws, 7 mm long.
Where it is used: alternate ground wire binding screw on rear panel, per official Kenwood installation manual.
Head and drive, as the source states them: binding head.
This entry is marked confirmed and comes from manualsdump.com.
M5 means a 5 mm nominal diameter with a 0.8 mm thread pitch. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Kenwood DPX-MP4070 car stereo ground/binding screw (accessory 4) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 7 mm | 0.8 mm | Binding head | not stated | Alternate ground wire binding screw on rear panel, per official Kenwood installation manual | Confirmed |
Fitment records and sources
Alternate ground wire binding screw on rear panel, per official Kenwood installation manual
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- Where the manufacturer publishes a torque value, use a torque driver rather than feel.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for binding head screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The record states 7 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- Wheelchair and mobility OEM screws specify an exact standard and strength class (ISO 7045 CL4.8, ISO 4762 CL12.9). Matching only the thread size can cause a failure under load.
- Ski and snowboard binding screws vary by brand and insert system (4x4, Channel, Tyrolia, Marker). Aftermarket suppliers standardise on M5/M6 but OEM screws can be a different pitch.
More in Vehicles, Marine & Mobility
ABB Terra DC Wallbox (3-phase UL)Adjustable Picatinny rail threaded insertAdult e-scootersAftermarket car stereo cageAirgun scope/rail mount replacement screwsAlpine Head UnitsAnalogis phono cartridge screw setArduino UNO / full-size Arduino boardsAudio MusiKraft cartridge mounting screw kitAudio MusiKraft cartridge/headshell mounting kitBar-end plug or bar-end shifterBerkel 330M Slicer carriage/guard fastener
Browse all 171 in Vehicles, Marine & Mobility →The same screw also fits
Devices whose records share a thread with Kenwood DPX-MP4070 car stereo ground/binding screw (accessory 4), closest length match first.
- HIWIN QHH35 / QEH20 linear guideway end-cap/lubrication unit fixing screws also M5 × 7 mm
- Shimano BL-M785 hydraulic brake lever also M5 × 7 mm
- Aftermarket car stereo cage also M5 × 7 mm
- Camera cage accessory arms also M5 × 7 mm
- QualGear QG-KIT-VA-3IN-B Projector Mounting Kit also M5 × 7 mm
- Faucet handle set screws also M5 × 7 mm
- DIN 965 / ISO 7046 countersunk Phillips screw also M5 × 7 mm
- DIN 912 socket-head cap screw also M5 × 7 mm
Questions about Kenwood DPX-MP4070 car stereo ground/binding screw (accessory 4) screws
- What size screw does Kenwood DPX-MP4070 car stereo ground/binding screw (accessory 4) use?
- M5 × 7 mm for alternate ground wire binding screw on rear panel, per official Kenwood installation manual.
- How long are the screws in Kenwood DPX-MP4070 car stereo ground/binding screw (accessory 4)?
- The record gives 7 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Kenwood DPX-MP4070 car stereo ground/binding screw (accessory 4)?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.