Kenwood XXV-05V Head Unit screw size
M5 · 6 mm long
Our records put Kenwood XXV-05V Head Unit on M5 screws, 6 mm long.
Where it is used: accessory screw for Toyota-style mounting brackets.
This entry is marked confirmed and comes from caraudio.manualsonline.com.
M5 means a 5 mm nominal diameter with a 0.8 mm thread pitch. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Kenwood XXV-05V Head Unit screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 6 mm | 0.8 mm | not stated | not stated | Accessory screw for Toyota-style mounting brackets | Confirmed |
Fitment records and sources
Accessory screw for Toyota-style mounting brackets.
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 6 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- M5x0.8 is the de facto universal bike thread — confirm 0.8mm pitch before threading into carbon or alloy bosses.
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with Kenwood XXV-05V Head Unit, closest length match first.
- Electrolux Professional compact rack-type dishwasher also M5 × 6 mm
- Marine-grade set/grub screw (DIN 916, A4 stainless) also M5 × 6 mm
- Makita GB801 also M5 × 6 mm
- Kenwood DPX-MP4070 car stereo ground/binding screw (accessory 3) also M5 × 6 mm
- Takara Belmont PRO III 047 dental chair also M5 × 6 mm
- Camera cage accessory arms also M5 × 6 mm
- Ottobock 17AD1 ankle joint screw (standard plastic) also M5 × 6 mm
- Berkel 330M Slicer cover fastener also M5 × 6 mm
Questions about Kenwood XXV-05V Head Unit screws
- What size screw does Kenwood XXV-05V Head Unit use?
- M5 × 6 mm for accessory screw for Toyota-style mounting brackets.
- How long are the screws in Kenwood XXV-05V Head Unit?
- The record gives 6 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Kenwood XXV-05V Head Unit?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.