Lenovo ThinkPad 600E screw size

Lenovo ThinkPad 600E screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M2.5, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 3–19.5 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Laptops & PCs

The same screw also fits

Devices whose records share a thread with Lenovo ThinkPad 600E, closest length match first.

• Dell Inspiron 13 7373 also M2 × 3 mm
• Acer Aspire 4930G also M2 × 3 mm
• Dell Inspiron 15 3530 (without USB Type-C) also M2 × 3 mm
• Lenovo ThinkPad X1 Extreme 2nd also M2 × 4 mm
• HP 13-4100 through 4199) also M2 × 4 mm
• Lenovo ThinkPad X13 Gen 4 also M2.5 × 3 mm
• Lenovo ideapad 320L-14IKB also M2 × 3 mm
• Lenovo ideapad 710S-13IKB also M2 × 4 mm

Questions about Lenovo ThinkPad 600E screws

What size screw does Lenovo ThinkPad 600E use?

M2 × 3 mm for unspecified (qty 2, silver); M2 × 4 mm for fan (qty 2, black); M2 × 4.8 mm for display (qty 8, black); M2 × 9.5 mm for card reader (qty 4, black); M2 × 9.5 mm for fan (qty 4, black); M2 × 9.5 mm for unspecified (qty 1, black); M2.5 × 16 mm for keyboard (qty 2, black); M2.5 × 19.5 mm for keyboard (qty 3, black); M2.5 × 3 mm for keyboard (qty 6, yellow); M2.5 × 3 mm for speaker (qty 6, yellow); M2.5 × 4.8 mm for I/O board (qty 2, black); M2.5 × 4.8 mm for display (qty 6, black); M2.5 × 4.8 mm for keyboard (qty 1, black); M2.5 × 4.8 mm for system board (qty 3, black); M2.5 × 4.8 mm for unspecified (qty 3, black); M2.5 × 7 mm for unspecified (qty 2, yellow).

How long are the screws in Lenovo ThinkPad 600E?

The records range from 3 to 19.5 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for Lenovo ThinkPad 600E?

The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Lenovo ThinkPad 600E?

TechSpareWarehouse (our own store) lists M2 x 3mm, M2 x 4mm and M2 x 5mm, which match lengths in the records above.