How long are the screws in Leviton EV Series charging pedestal (EPED1 / EPED2)?

The records range from 12 to 22 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M5 screw?

0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.

What screwdriver do I need for Leviton EV Series charging pedestal (EPED1 / EPED2)?

The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.

Can I use an imperial screw instead of M5?

No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.

Leviton EV Series charging pedestal (EPED1 / EPED2) screw size

M5 · 12 to 22 mm long

If you are replacing a screw on Leviton EV Series charging pedestal (EPED1 / EPED2), the thread is M5 in lengths from 12 to 22 mm.

Where it is used: M5 x 22mm connector base / hook screws (x4) and M5 x 12mm station mounting and wiring window screws.

This entry is marked confirmed and comes from leviton.com.

M5 means a 5 mm nominal diameter with a 0.8 mm thread pitch. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing.

Leviton EV Series charging pedestal (EPED1 / EPED2) screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M5	12–22 mm	0.8 mm	not stated	not stated	M5 x 22mm connector base / hook screws (x4) and M5 x 12mm station mounting and wiring window screws	Confirmed

Fitment records and sources

M512-22mmconfirmed

M5 x 22mm connector base / hook screws (x4) and M5 x 12mm station mounting and wiring window screws

pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25

Source

How to check the screw before you buy

Board standoffs and enclosure bosses set the usable length: the screw should clamp the board without bottoming in the standoff.
Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The records span 12–22 mm, which means different positions take different lengths — match each hole to its own screw.
Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.

Common mix-ups with M5

Sensor barrel sizes like M8, M12, M18 and M30 name the sensor body or connector diameter, not a mounting screw — check whether the M number is a body thread before buying screws.
M5x0.8 is the de facto universal bike thread — confirm 0.8mm pitch before threading into carbon or alloy bosses.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Electronics, Racks & Enclosures

19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw 19-inch rack network and AV gear 19-inch rack-mount audio/AV equipment 19-inch server racks 19in / 10in server rack cage nut and screw kit 19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)

Browse all 357 in Electronics, Racks & Enclosures →

The same screw also fits

Devices whose records share a thread with Leviton EV Series charging pedestal (EPED1 / EPED2), closest length match first.

Alpha Series forklift mast bracket also M5 × 16 mm
Bike rack & fender eyelets also M5 × 12–20 mm
Shelving brackets also M5 × 12–22 mm
Rack-mount network and AV equipment also M5 × 19 mm
Rear-view / side mirror bracket also M5 × 12–16 mm
Rack and fender eyelets also M5 × 12–16 mm
Badger Meter M5000 Remote Junction Box Kit also M5 × 16 mm
RF Elements Twin Horn antenna bracket (secondary hardware) also M5 × 12 mm

Questions about Leviton EV Series charging pedestal (EPED1 / EPED2) screws

What size screw does Leviton EV Series charging pedestal (EPED1 / EPED2) use?: M5 × 12–22 mm for M5 x 22mm connector base / hook screws (x4) and M5 x 12mm station mounting and wiring window screws.
How long are the screws in Leviton EV Series charging pedestal (EPED1 / EPED2)?: The records range from 12 to 22 mm depending on the position, so match each screw to its own hole.
What is the thread pitch of an M5 screw?: 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
What screwdriver do I need for Leviton EV Series charging pedestal (EPED1 / EPED2)?: The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
Can I use an imperial screw instead of M5?: No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.

Heads up: shipping delay