Rear-view / side mirror bracket screw size
M5 · 10 to 16 mm long
If you are replacing a screw on Rear-view / side mirror bracket, the thread is M5 in lengths from 10 to 16 mm.
The record covers mirror bracket fasteners.
This entry is marked reported.
M5 means a 5 mm nominal diameter with a 0.8 mm thread pitch. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Rear-view / side mirror bracket screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 10–16 mm | 0.8 mm | not stated | not stated | Mirror bracket fasteners | Reported |
Fitment records and sources
Mirror bracket fasteners
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- Board standoffs and enclosure bosses set the usable length: the screw should clamp the board without bottoming in the standoff.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 10–16 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- Espresso/coffee-equipment M5 and M6 socket-head screws (DIN 7984/UNI 9327) are cross-brand standard fasteners shared across CMA, Astoria, and La Cimbali brewing-group hardware, so a single screw often services multiple manufacturers' machines.
- M5x0.8 is the de facto universal bike thread — confirm 0.8mm pitch before threading into carbon or alloy bosses.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M5 x 10mm Black Wafer Head Bike Fender & Rack Screws for Tern MTR Fenders, Blackburn EX-1 Rack, ENVO Stax & René Herse Fender Set – 10-Pack Replacement
$5.99Choose size -
M5 x 10mm Black Wafer Head Folding Mechanism Screws for GOTRAX GXL V2, Rival, XR Ultra & XR Elite – 10-Pack Replacement
$5.99Choose size -
M5 x 12mm Black Wafer Head Cut-off Saw Screws for STIHL TS400 Cut-off Saw (replaces IS-M5x12 9022 341 0960) – 10-Pack Replacement
$5.99Choose size -
M5 x 12mm Black Wafer Head Generator Cover Screws for Honda EM, EB, EG Generators & EU3200i (replaces 90102-Z21-000) – 10-Pack Replacement
$5.99Choose size
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with Rear-view / side mirror bracket, closest length match first.
- Rack and fender eyelets also M5 × 10–16 mm
- Marine-grade set/grub screw (DIN 916, A4 stainless) also M5 × 10 mm
- Triumph Thruxton rear mounting bracket also M5 × 12 mm
- BYD Battery-Box Premium LVS also M5 × 14 mm
- RF Elements Twin Horn antenna bracket (secondary hardware) also M5 × 12 mm
- Badger Meter M5000 Remote Junction Box Kit also M5 × 16 mm
- Leviton EV Series charging pedestal (EPED1 / EPED2) also M5 × 12–16 mm
- Alpha Series forklift mast bracket also M5 × 16 mm
Questions about Rear-view / side mirror bracket screws
- What size screw does Rear-view / side mirror bracket use?
- M5 × 10–16 mm for mirror bracket fasteners.
- How long are the screws in Rear-view / side mirror bracket?
- The records range from 10 to 16 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Rear-view / side mirror bracket?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.