Makita DTW1004 cordless impact wrench screw size
M5 · 35 mm long
The screws used on Makita DTW1004 cordless impact wrench are M5, 35 mm long.
It is listed for housing/frame bolts, "H.S.H.BOLT M5X35 WITH WRM" x4.
This entry is marked confirmed and comes from makita.ca.
An M5 screw is 5 mm in diameter with a 0.8 mm pitch, tapped with a 4.2 mm drill; imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Makita DTW1004 cordless impact wrench screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 35 mm | 0.8 mm | not stated | not stated | Housing/frame bolts, "H.S.H.BOLT M5X35 WITH WRM" x4 | Confirmed |
Fitment records and sources
Housing/frame bolts, "H.S.H.BOLT M5X35 WITH WRM" x4
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- Industrial parts lists usually give the full callout (thread, length, head, grade); match all four, not just the thread.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 35 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- Stacking frame + rack tab + fender stay needs 18-20mm bolts, not the 12-16mm that come with a cage.
- Truss and stage-light clamps use M8 or M10 bolts depending on tube diameter — larger than anything in this database, so don't substitute an M6.
More in Industrial & Machinery
ABB ACS580 motor terminal box / cable glandsABB ACS580 terminal hardware (frames R3-R5)ABB random-wound motor terminal boxes (ACS580 drive systems)Allen-Bradley ControlLogix 1756-A chassisAngle grinder gear housingBianchi / Nuova Simonelli / Rheavendors / Saeco vending machineCircular saw blade guard pivotContender Planetary Mixer MXP004/MXP005 (commercial bakery mixer) electrical diagram terminal screwsCordless drill housing shellsCOSEL power supply terminal block (used in industrial/pump/water-treatment control panels)Datalogic DS2400 fixed-mount barcode readerDeWalt D51430 / D51431 pneumatic nailer
Browse all 113 in Industrial & Machinery →The same screw also fits
Devices whose records share a thread with Makita DTW1004 cordless impact wrench, closest length match first.
- Cordless drill housing shells also M5 × 35 mm
- ABB ACS580 motor terminal box / cable glands also M5 × 35 mm
- Makita 1806B planer also M5 × 35 mm
- LG 50PZ950U also M5 × 35 mm
- LG 60PZ950U also M5 × 35 mm
- LG 55LW9500 also M5 × 35 mm
- LG 60LW9500 also M5 × 35 mm
- LG 60PZ950 also M5 × 35 mm
Questions about Makita DTW1004 cordless impact wrench screws
- What size screw does Makita DTW1004 cordless impact wrench use?
- M5 × 35 mm for housing/frame bolts, "H.S.H.BOLT M5X35 WITH WRM" x4.
- How long are the screws in Makita DTW1004 cordless impact wrench?
- The record gives 35 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Makita DTW1004 cordless impact wrench?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.