Molex 1U Specification Grade Fiber Enclosure screw size
M4 · length not stated in the sources
Our records put Molex 1U Specification Grade Fiber Enclosure on M4 screws. None of the sources we found gives an exact length, so measure the original before you order.
The record covers M4 screws used for adjustable rack-ear and panel mounting hardware inside 1U fiber enclosure.
This entry is marked reported and comes from molexces.com.
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Molex 1U Specification Grade Fiber Enclosure screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | not stated | 0.7 mm | not stated | not stated | M4 screws used for adjustable rack-ear and panel mounting hardware inside 1U fiber enclosure | Reported |
Fitment records and sources
M4 screws used for adjustable rack-ear and panel mounting hardware inside 1U fiber enclosure
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Grounding-lug screws on Siemens and Beckhoff gear (M4) are earth hardware, not structural mounting screws — don't reuse them to hold a module.
- Not all telescope/finder hardware is metric — Celestron Edge/NexStar SE finder-shoe and dovetail screws are reported as 8/32 (imperial UNC), so metric M4/M5 fitments cannot be assumed across all Celestron products; must check per accessory/vintage.
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with Molex 1U Specification Grade Fiber Enclosure, closest length match first.
- Korg EX-8000 / M1R rack ear replacement also M4
- Vertical trolley 48V 280Ah battery enclosure also M4
- Hammond 1557 series polycarbonate/ABS watertight enclosure lid screws also M4
- Elo self-service kiosk peripheral mount also M4
- Neopost/Paper-Machines 7104 Series High-Volume Modular Inserter (mailroom sorting/inserting machine) also M4
- Phoenix Contact CHARX EV charging connector also M4
- Banner Engineering PVA sensors (SMBPVA6 bracket) also M4
- Keystone Electronics metric nylon standoff also M4
Questions about Molex 1U Specification Grade Fiber Enclosure screws
- What size screw does Molex 1U Specification Grade Fiber Enclosure use?
- M4 for M4 screws used for adjustable rack-ear and panel mounting hardware inside 1U fiber enclosure.
- How long are the screws in Molex 1U Specification Grade Fiber Enclosure?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Molex 1U Specification Grade Fiber Enclosure?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.