Vertical trolley 48V 280Ah battery enclosure screw size
M4 · length not stated in the sources
Our records put Vertical trolley 48V 280Ah battery enclosure on M4 screws. None of the sources we found gives an exact length, so measure the original before you order.
It is listed for dust screens on both sides fixed with M4 flange screws/nuts.
This entry is marked confirmed and comes from nkon.nl.
For reference, M4 is 4 mm across the threads at 0.7 mm pitch. The imperial size people confuse it with: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Vertical trolley 48V 280Ah battery enclosure screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | not stated | 0.7 mm | not stated | not stated | Dust screens on both sides fixed with M4 flange screws/nutswasher / flange face | Confirmed |
Fitment records and sources
Dust screens on both sides fixed with M4 flange screws/nuts
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Grounding/earth-stud screws on hazardous-area (ATEX/IECEx) gas detectors are commonly M4 even though the enclosure body uses larger threaded glands — don't extrapolate the earth screw size to the whole unit.
- M4 and 6-32 UNC share a nominal diameter with different pitch — a classic cross-thread in US-market kits.
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with Vertical trolley 48V 280Ah battery enclosure, closest length match first.
- Molex 1U Specification Grade Fiber Enclosure also M4
- Korg EX-8000 / M1R rack ear replacement also M4
- Elo self-service kiosk peripheral mount also M4
- Hammond 1557 series polycarbonate/ABS watertight enclosure lid screws also M4
- Phoenix Contact CHARX EV charging connector also M4
- Neopost/Paper-Machines 7104 Series High-Volume Modular Inserter (mailroom sorting/inserting machine) also M4
- Keystone Electronics metric nylon standoff also M4
- Banner Engineering PVA sensors (SMBPVA6 bracket) also M4
Questions about Vertical trolley 48V 280Ah battery enclosure screws
- What size screw does Vertical trolley 48V 280Ah battery enclosure use?
- M4 for dust screens on both sides fixed with M4 flange screws/nuts.
- How long are the screws in Vertical trolley 48V 280Ah battery enclosure?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Vertical trolley 48V 280Ah battery enclosure?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.