NBK SSCZS-M1.4 miniature captive screw screw size
M1.4 · length not stated in the sources
If you are replacing a screw on NBK SSCZS-M1.4 miniature captive screw, the thread is M1.4. None of the sources we found gives an exact length, so measure the original before you order.
It is listed for pan-head captive machine screw catalogued for precision medical and optical instruments.
Head and drive, as the source states them: pan head.
This entry is marked likely and comes from nbk1560.com.
An M1.4 screw is 1.4 mm in diameter with a 0.3 mm pitch, tapped with a 1.1 mm drill; imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
NBK SSCZS-M1.4 miniature captive screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | not stated | 0.3 mm | Pan head | not stated | Pan-head captive machine screw catalogued for precision medical and optical instrumentscaptive | Likely |
Fitment records and sources
Pan-head captive machine screw catalogued for precision medical and optical instruments
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- Camera and optics hardware often uses short screws into thin threaded plates, so check engagement before tightening fully.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for pan head screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- Driver: the source does not name the drive. Standard M1.4 heads take PH000 / PH00 for Phillips and T2–T3 for Torx, and a 1.3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- Whoop drone M1.4 comes in steel, PEEK and RENY versions: plastic ones are for cameras, not structural frame use.
- M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.
More in Cameras & Optics
The same screw also fits
Devices whose records share a thread with NBK SSCZS-M1.4 miniature captive screw, closest length match first.
- Eyeglass spring hinge barrel also M1.4
- Rimless eyewire tension screw also M1.4
- JIS/ISO metric camera and lens internal screws (JCIS #0 driver family) also M1.4
- Captive pan-head miniature screw for precision instruments (NBK SSCZS series) also M1.4
- General eyewear/smart-glasses hinge and temple screws also M1.4
- Binocular hinge / bridge also M1.4
- Eyeglass hinge screw (the most common size) also M1.4
- Self-aligning spring hinge screw (Tabco Optical) also M1.4
Questions about NBK SSCZS-M1.4 miniature captive screw screws
- What size screw does NBK SSCZS-M1.4 miniature captive screw use?
- M1.4 for pan-head captive machine screw catalogued for precision medical and optical instruments.
- How long are the screws in NBK SSCZS-M1.4 miniature captive screw?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for NBK SSCZS-M1.4 miniature captive screw?
- The sources do not name the drive. For M1.4, Phillips heads normally take PH000 / PH00 and Torx heads T2–T3; socket heads take a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.