Rimless eyewire tension screw screw size
M1.4 · 3 to 5 mm long
Rimless eyewire tension screw takes M1.4 metric screws in lengths from 3 to 5 mm.
The record covers clamps the lens edge into the rimless bracket.
This entry is marked reported and comes from qtena.com.
M1.4 means a 1.4 mm nominal diameter with a 0.3 mm thread pitch. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
Rimless eyewire tension screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | 3–5 mm | 0.3 mm | not stated | not stated | clamps the lens edge into the rimless bracket | Reported |
Fitment records and sources
clamps the lens edge into the rimless bracket
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- Do not confuse metric mounting screws with the 1/4-20 or 3/8-16 tripod threads that cameras and clamps also carry.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 3–5 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M1.4 heads take PH000 / PH00 for Phillips and T2–T3 for Torx, and a 1.3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- Whoop drone M1.4 comes in steel, PEEK and RENY versions: plastic ones are for cameras, not structural frame use.
- M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Cameras & Optics
1.25" eyepiece/diagonal/SCT visual back thumb screwAimpoint Comp M4 / M4s LRP & TNP mountAimpoint Micro T-1/T-2/H-1/H-2 standard mountAimpoint Micro T-1/T-2/H-1/H-2 standard mount screwAimpoint SM-2001/2007 Micro T1/T2 mountAirsoft red dot sight mounting screw set (Laylax/Quintes Sence)Airsoft/firearm red-dot sight optic mounting screws (Vortex Viper, Swampfox patterns)Alpine and touring ski bindings (Binding Freedom inserts)Arca-style quick-release plateARRI plate for Sony VENICE 1/2Artesky 340mm Vixen Dovetail BarAstromania finder scope dovetail base
Browse all 278 in Cameras & Optics →The same screw also fits
Devices whose records share a thread with Rimless eyewire tension screw, closest length match first.
- Eyeglass spring hinge barrel also M1.4 × 3–5 mm
- Binocular hinge / bridge also M1.4 × 3–5 mm
- Eyeglass hinge screw (the most common size) also M1.4 × 3–5 mm
- Oakley O Matter / steel frame hinge also M1.4 × 3–4 mm
- Eyeglass hinge / eyewire screw also M1.4 × 3.8 mm
- Camera lens/body low-profile 'JIS Micro Profile' fastener also M1.4 × 4 mm
- Compact & action cameras also M1.4 × 3–4 mm
- Universal eyeglass hinge screw (2.0mm head) also M1.4 × 4 mm
Questions about Rimless eyewire tension screw screws
- What size screw does Rimless eyewire tension screw use?
- M1.4 × 3–5 mm for clamps the lens edge into the rimless bracket.
- How long are the screws in Rimless eyewire tension screw?
- The records range from 3 to 5 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for Rimless eyewire tension screw?
- The sources do not name the drive. For M1.4, Phillips heads normally take PH000 / PH00 and Torx heads T2–T3; socket heads take a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.