Oakley O Matter / steel frame hinge screw size
M1.4 · 2 to 4 mm long
If you are replacing a screw on Oakley O Matter / steel frame hinge, the thread is M1.4 in lengths from 2 to 4 mm.
Where it is used: common replacement on Holbrook Ti and steel-line hinges.
This entry is marked reported and comes from shuntool.com.
For reference, M1.4 is 1.4 mm across the threads at 0.3 mm pitch. The imperial size people confuse it with: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
Oakley O Matter / steel frame hinge screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | 2–4 mm | 0.3 mm | not stated | not stated | common replacement on Holbrook Ti and steel-line hinges | Reported |
Fitment records and sources
common replacement on Holbrook Ti and steel-line hinges
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- Camera and optics hardware often uses short screws into thin threaded plates, so check engagement before tightening fully.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 2–4 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M1.4 heads take PH000 / PH00 for Phillips and T2–T3 for Torx, and a 1.3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- Whoop drone M1.4 comes in steel, PEEK and RENY versions: plastic ones are for cameras, not structural frame use.
- M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M1.4 x 2mm Screws for Dell XPS 13 9340 Power Button Fingerprint 10-Pack Black
$4.99 -
M1.4 x 2mm Screws for Dell XPS 14 9440 Power Button – 10-Pack Black
$4.99
-
M1.4 Phillips Flat Head Carbon Steel Machine Screws (Multiple Lengths & Finishes)
$5.00Choose size -
M1.4 x 2mm Micro Screws for Harmonica Reed Plate Repair 10-Pack
$4.99
More in Cameras & Optics
1.25" eyepiece/diagonal/SCT visual back thumb screwAimpoint Comp M4 / M4s LRP & TNP mountAimpoint Micro T-1/T-2/H-1/H-2 standard mountAimpoint Micro T-1/T-2/H-1/H-2 standard mount screwAimpoint SM-2001/2007 Micro T1/T2 mountAirsoft red dot sight mounting screw set (Laylax/Quintes Sence)Airsoft/firearm red-dot sight optic mounting screws (Vortex Viper, Swampfox patterns)Alpine and touring ski bindings (Binding Freedom inserts)Arca-style quick-release plateARRI plate for Sony VENICE 1/2Artesky 340mm Vixen Dovetail BarAstromania finder scope dovetail base
Browse all 278 in Cameras & Optics →The same screw also fits
Devices whose records share a thread with Oakley O Matter / steel frame hinge, closest length match first.
- Eyeglass hinge / eyewire screw also M1.4 × 3.8 mm
- Binocular hinge / bridge also M1.4 × 3–4 mm
- Eyeglass hinge screw (the most common size) also M1.4 × 2–4 mm
- Eyeglass spring hinge barrel also M1.4 × 3–4 mm
- Rimless eyewire tension screw also M1.4 × 3–4 mm
- Eyewire/optical and precision-instrument screws (representative of hearing aid / camera size class) also M1.4 × 3.5–4 mm
- Compact & action cameras also M1.4 × 2–4 mm
- Universal eyeglass hinge screw (2.0mm head) also M1.4 × 4 mm
Questions about Oakley O Matter / steel frame hinge screws
- What size screw does Oakley O Matter / steel frame hinge use?
- M1.4 × 2–4 mm for common replacement on Holbrook Ti and steel-line hinges.
- How long are the screws in Oakley O Matter / steel frame hinge?
- The records range from 2 to 4 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for Oakley O Matter / steel frame hinge?
- The sources do not name the drive. For M1.4, Phillips heads normally take PH000 / PH00 and Torx heads T2–T3; socket heads take a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Oakley O Matter / steel frame hinge?
- TechSpareWarehouse (our own store) lists M1.4 x 2mm, which matches the length in the records above.