Rotary tool (Dremel) housing screw size
M2.5 · 6 to 10 mm long
Our records put Rotary tool (Dremel) housing on M2.5 screws in lengths from 6 to 10 mm.
Where it is used: collet housing and motor casing.
This entry is marked reported and comes from ifixit.com.
For reference, M2.5 is 2.5 mm across the threads at 0.45 mm pitch. The imperial size people confuse it with: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in.
Rotary tool (Dremel) housing screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2.5 | 6–10 mm | 0.45 mm | not stated | not stated | collet housing and motor casing | Reported |
Fitment records and sources
collet housing and motor casing
pitch 0.45 mm · tap 2.05 mm · clearance 2.9 mm · PH1 / Torx T8
How to check the screw before you buy
- Check the strength class stamped on the head (8.8, 10.9, A2-70) and replace like for like.
- Diameter: across the threads an M2.5 screw measures about 2.5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.45 mm from one thread crest to the next (22.22 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 6–10 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2.5 heads take PH1 for Phillips and T8 for Torx, and a 2 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2.5 is about 45-70 N·cm into metal threads and 20-35 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2.5
- M2.5 pitch is 0.45mm vs M3's 0.5mm and M2's 0.4mm — forcing the wrong one strips plastic bosses instantly.
- M2.5 and M3 look the same to the naked eye — you need calipers on the shank to tell them apart.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2.5 x 6mm Laptop Motherboard Replacement Screws Wafer Head 10-Pack Black
$4.99 -
10x M2.5 x 6mm Phillips Screws for Lenovo ThinkPad X131e Chromebook LCD Hinge
$4.99
-
M2.5 x 8mm Screws for Retevis RT27 Radio Belt Clip 10-Pack Black Phillips
$4.99 -
M2.5 x 8mm Screws for Raspberry Pi 5 Case and PoE HAT 10-Pack Black
$4.99 -
M2.5 x 10mm Phillips Wafer Head Screw for Turntable Cartridge Headshell Mount - Pack of 50 Black
$5.99 -
M2.5 x 10mm Phillips Wafer Head Screw for ASUS TUF Gaming A15/F15 Laptop Repair - Single Replacement Black
$0.10 each · min. 50
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
-
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
More in Industrial & Machinery
ABB ACS580 motor terminal box / cable glandsABB ACS580 terminal hardware (frames R3-R5)ABB random-wound motor terminal boxes (ACS580 drive systems)Allen-Bradley ControlLogix 1756-A chassisAngle grinder gear housingBianchi / Nuova Simonelli / Rheavendors / Saeco vending machineCircular saw blade guard pivotContender Planetary Mixer MXP004/MXP005 (commercial bakery mixer) electrical diagram terminal screwsCordless drill housing shellsCOSEL power supply terminal block (used in industrial/pump/water-treatment control panels)Datalogic DS2400 fixed-mount barcode readerDeWalt D51430 / D51431 pneumatic nailer
Browse all 113 in Industrial & Machinery →The same screw also fits
Devices whose records share a thread with Rotary tool (Dremel) housing, closest length match first.
- Juki industrial sewing machine needle-area hardware also M2.5 × 6 mm
- Milwaukee cordless tool (service bulletin 54-26-2590) also M2.5 × 6 mm
- HP Compaq 515 also M2.5 × 6 mm
- HP ProBook x360 435 G8 also M2.5 × 7 mm
- Dell G3 17 3779 also M2.5 × 7 mm
- Lenovo E31-70 also M2.5 × 6 mm
- Lenovo ThinkPad A22P also M2.5 × 7 mm
- Lenovo Chromebook C330 also M2.5 × 7 mm
Questions about Rotary tool (Dremel) housing screws
- What size screw does Rotary tool (Dremel) housing use?
- M2.5 × 6–10 mm for collet housing and motor casing.
- How long are the screws in Rotary tool (Dremel) housing?
- The records range from 6 to 10 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2.5 screw?
- 0.45 mm (coarse), which is the standard pitch for M2.5 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.05 mm and the normal clearance hole is 2.9 mm.
- What screwdriver do I need for Rotary tool (Dremel) housing?
- The sources do not name the drive. For M2.5, Phillips heads normally take PH1 and Torx heads T8; socket heads take a 2 mm hex key.
- Can I use an imperial screw instead of M2.5?
- No. Imperial look-alike: #3-48 / #4-40 (2.51 / 2.84 mm) — #4-40 is the common US stand-in and it will NOT thread in. Use a true M2.5 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Rotary tool (Dremel) housing?
- TechSpareWarehouse (our own store) lists M2.5 x 6mm, M2.5 x 8mm and M2.5 x 10mm, which match lengths in the records above.