Samsung Galaxy A01/A02/A03/A04/A05/A06/A10 screw size
M1.4 · 2.3 mm long
The screws used on Samsung Galaxy A01/A02/A03/A04/A05/A06/A10 are M1.4, 2.3 mm long.
It is listed for motherboard & back-cover bracket screws, part 6001-001460.
This entry is marked confirmed and comes from shop.headlane.co.uk.
M1.4 means a 1.4 mm nominal diameter with a 0.3 mm thread pitch. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
Samsung Galaxy A01/A02/A03/A04/A05/A06/A10 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | 2.3 mm | 0.3 mm | not stated | not stated | motherboard & back-cover bracket screws, part 6001-001460 | Confirmed |
Fitment records and sources
motherboard & back-cover bracket screws, part 6001-001460
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- Board standoffs and enclosure bosses set the usable length: the screw should clamp the board without bottoming in the standoff.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 2.3 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M1.4 heads take PH000 / PH00 for Phillips and T2–T3 for Torx, and a 1.3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with Samsung Galaxy A01/A02/A03/A04/A05/A06/A10, closest length match first.
- Samsung Galaxy S23 screen/battery assembly also M1.4 × 2.3 mm
- Watch casebacks & dials also M1.4 × 2.3 mm
- Eyeglass hinge screw (the most common size) also M1.4 × 2.3 mm
- NBK SPE-MC PEEK micro pan head screws also M1.4 × 2.3 mm
- Spectacle frame hinge screws (ISO 11381 standard) also M1.4 × 2.3 mm
- Samsung Galaxy S23 USB-C daughterboard also M1.4 × 2.3 mm
- Ultrabook antenna clips also M1.4 × 2.3 mm
- Hearing aid shells also M1.4 × 2.3 mm
Questions about Samsung Galaxy A01/A02/A03/A04/A05/A06/A10 screws
- What size screw does Samsung Galaxy A01/A02/A03/A04/A05/A06/A10 use?
- M1.4 × 2.3 mm for motherboard & back-cover bracket screws, part 6001-001460.
- How long are the screws in Samsung Galaxy A01/A02/A03/A04/A05/A06/A10?
- The record gives 2.3 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for Samsung Galaxy A01/A02/A03/A04/A05/A06/A10?
- The sources do not name the drive. For M1.4, Phillips heads normally take PH000 / PH00 and Torx heads T2–T3; socket heads take a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.