Screw-in stabilizers (Cherry-style) screw size
M2 · 5 to 6 mm long
The screws used on Screw-in stabilizers (Cherry-style) are M2 in lengths from 5 to 6 mm.
It is listed for mounts screw-in stabs to the keyboard PCB.
This entry is marked reported and comes from cherrymx.de.
For reference, M2 is 2 mm across the threads at 0.4 mm pitch. The imperial size people confuse it with: #2-56 UNC (2.18 mm) is close but not interchangeable.
Screw-in stabilizers (Cherry-style) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 5–6 mm | 0.4 mm | not stated | not stated | mounts screw-in stabs to the keyboard PCB | Reported |
Fitment records and sources
mounts screw-in stabs to the keyboard PCB
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
How to check the screw before you buy
- Laptop covers and brackets often mix two or three lengths of the same thread, so lay the screws out in the order they came out (a magnetic mat or a sheet of paper with the hole pattern drawn on it works).
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 5–6 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2
- The standard M.2 SSD screw is M2 x 3mm, but some laptops and handhelds use non-standard lengths or head shapes.
- M2 (2.00mm, 0.4mm pitch) is NOT the same as #2-56 UNC (2.18mm) — close enough to cross-thread and strip if forced.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 5mm Replacement Bottom Case Screws for Dell Inspiron 3535 Laptop 10-Pack
$4.99 -
M2 x 5mm Phillips Wafer Head Screw for Dell G16 7630 Gaming Laptop Repair - Pack of 100 Black
$7.99 -
M2 x 6mm Phillips Wafer Head Screw for HP Omen Gaming Laptop Repair - Pack of 100 Black
$7.99 -
M2 x 6mm Phillips Wafer Head Screw for Audiophile Headphone Headband Repair - Pack of 50 Black
$4.99
-
ASUS ROG Strix G15 G513R Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size -
ASUS ROG Strix G17 G713 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 3mm, M2.5 x 6mm Phillips Wafer Head, Black
$0.10Choose size
-
M2 x 6mm Phillips Wafer Head Screw for EDC Multi-Tool Handle Scale - Pack of 100 Black
$7.99
-
M2 x 6mm Phillips Wafer Head Screw for FPV Drone Build & Repair - Pack of 100 Black
$7.99
More in Laptops & PCs
2.5in drive trays & caddiesAcer / MSI laptopsAcer 5510/4020 series I/O and misc chassis screwsAcer 7520 / 7220Acer Aspire / Swift bottom coverAcer Aspire / Swift M.2 SSDAcer Aspire 1310Acer Aspire 1410Acer Aspire 1420PAcer Aspire 1650Acer Aspire 1680Acer Aspire 1690
Browse all 2799 in Laptops & PCs →The same screw also fits
Devices whose records share a thread with Screw-in stabilizers (Cherry-style), closest length match first.
- Lenovo ideapad 320R-17AST also M2 × 6 mm
- Dell Latitude 5340 also M2 × 5 mm
- HP Pavilion ZE2000 also M2 × 5 mm
- Lenovo E4325 also M2 × 6 mm
- HP Compaq 6720T also M2 × 6 mm
- LG LS50 also M2 × 5 mm
- Dell Latitude 5290 also M2 × 5 mm
- Dell Inspiron 14 5488 also M2 × 5 mm
Questions about Screw-in stabilizers (Cherry-style) screws
- What size screw does Screw-in stabilizers (Cherry-style) use?
- M2 × 5–6 mm for mounts screw-in stabs to the keyboard PCB.
- How long are the screws in Screw-in stabilizers (Cherry-style)?
- The records range from 5 to 6 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Screw-in stabilizers (Cherry-style)?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Screw-in stabilizers (Cherry-style)?
- TechSpareWarehouse (our own store) lists M2 x 5mm and M2 x 6mm, which match lengths in the records above.