How long are the screws in Sea-Doo personal watercraft phillips screw?

The record gives 12 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.

What is the thread pitch of an M5 screw?

0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.

What screwdriver do I need for Sea-Doo personal watercraft phillips screw?

The source lists a Phillips drive. Standard M5 heads otherwise take PH2 (Phillips) or T25 (Torx), or a 4 mm hex key.

Can I use an imperial screw instead of M5?

No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.

Sea-Doo personal watercraft phillips screw screw size

M5 · 12 mm long

Our records put Sea-Doo personal watercraft phillips screw on M5 screws, 12 mm long.

It is listed for genuine Sea-Doo spare part, phillips screw used on GTI/GTX/RX/LRV model lines.

Head and drive, as the source states them: Phillips drive.

This entry is marked confirmed and comes from bike-parts-sea-doo.com.

For reference, M5 is 5 mm across the threads at 0.8 mm pitch. The imperial size people confuse it with: #10-32 (4.83 mm) — the other common rack thread; check before mixing.

Sea-Doo personal watercraft phillips screw screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M5	12 mm	0.8 mm	not stated	Phillips	Genuine Sea-Doo spare part, phillips screw used on GTI/GTX/RX/LRV model lines	Confirmed

Fitment records and sources

M512mmconfirmed

Genuine Sea-Doo spare part, phillips screw used on GTI/GTX/RX/LRV model lines

pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25

Source

How to check the screw before you buy

Frame and motor screws must not reach the motor windings; check the length against the motor's mounting depth.
Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The record states 12 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
Driver: the source names a Phillips drive. For comparison, standard M5 heads take PH2 (Phillips) or T25 (Torx), or a 4 mm hex key.
Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.

Common mix-ups with M5

M5x0.8 is the de facto universal bike thread — confirm 0.8mm pitch before threading into carbon or alloy bosses.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Drones, RC & Gimbals

1/10 scale RC cars 1/8 scale RC car chassis hardware 3D-printed FPV stack mounts and spacers 5-inch brushless motor to arm Airsoft V2 / EHPA gearbox shells ALware Quad Flyer Spider 500 quadcopter kit Antique wall clock pendulum brackets Arcade marquee retainers ARRMA Senton (and similar 1/10 vehicles)ARRMA Senton/kingpin-equipped vehicles Axial Racing crawler/buggy kits Axial SCX10 III RC crawler chassis

Browse all 144 in Drones, RC & Gimbals →

The same screw also fits

Devices whose records share a thread with Sea-Doo personal watercraft phillips screw, closest length match first.

Home safe hinge and strike bolts also M5 × 12 mm
Large / industrial drones also M5 × 12 mm
OpenBuilds V-Slot T-nut bolts also M5 × 12 mm
Leviton EV Series charging pedestal (EPED1 / EPED2) also M5 × 12 mm
E-scooter deck & folding covers also M5 × 12 mm
Xiaomi M365 / Ninebot deck cover also M5 × 12 mm
Bike rack & fender eyelets also M5 × 12 mm
Bike kickstand plates also M5 × 12 mm

Questions about Sea-Doo personal watercraft phillips screw screws

What size screw does Sea-Doo personal watercraft phillips screw use?: M5 × 12 mm for genuine Sea-Doo spare part, phillips screw used on GTI/GTX/RX/LRV model lines.
How long are the screws in Sea-Doo personal watercraft phillips screw?: The record gives 12 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
What is the thread pitch of an M5 screw?: 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
What screwdriver do I need for Sea-Doo personal watercraft phillips screw?: The source lists a Phillips drive. Standard M5 heads otherwise take PH2 (Phillips) or T25 (Torx), or a 4 mm hex key.
Can I use an imperial screw instead of M5?: No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.

Heads up: shipping delay