Segway-Ninebot Grade 10.9 structural screw (part 10.01.3188.00) screw size
M4 · 16 mm long
The screws used on Segway-Ninebot Grade 10.9 structural screw (part 10.01.3188.00) are M4, 16 mm long.
The record covers hex socket cylindrical head, galvanised carbon steel, drop-resistance rated.
Head and drive, as the source states them: Hex socket (Allen) drive.
This entry is marked reported and comes from fixpart.ie.
For reference, M4 is 4 mm across the threads at 0.7 mm pitch. The imperial size people confuse it with: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Segway-Ninebot Grade 10.9 structural screw (part 10.01.3188.00) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 16 mm | 0.7 mm | not stated | Hex socket (Allen) | Hex socket cylindrical head, galvanised carbon steel, drop-resistance rated | Reported |
Fitment records and sources
Hex socket cylindrical head, galvanised carbon steel, drop-resistance rated
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- On vehicles and bikes, use the original strength class and finish; outdoor hardware is usually stainless or coated to resist corrosion.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 16 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Hex socket (Allen) drive. For comparison, standard M4 heads take PH2 (Phillips) or T20 (Torx), or a 3 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Camera rig/cage accessories (SmallRig, Wooden Camera/Metabones) frequently mix M4 structural screws with 1/4-20 and 3/8-16 imperial mounting points on the same product — verify which specific fastener a manual is referencing before ordering replacements.
- Grounding-lug screws on Siemens and Beckhoff gear (M4) are earth hardware, not structural mounting screws — don't reuse them to hold a module.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Vehicles, Marine & Mobility
The same screw also fits
Devices whose records share a thread with Segway-Ninebot Grade 10.9 structural screw (part 10.01.3188.00), closest length match first.
- RV / camper cabinet hardware also M4 × 16 mm
- Drawer slide rails also M4 × 16 mm
- Chainsaw air filter cover also M4 × 16 mm
- Segway-Ninebot Chassis/body hex countersunk screw (part 01.12.0411.00) also M4 × 16 mm
- Motorcycle fairing panels also M4 × 16 mm
- DeWalt D51430 / D51431 pneumatic nailer also M4 × 16 mm
- LG 55LV5400 also M4 × 16 mm
- Hotpoint / Indesit / Ariston washing machine also M4 × 16 mm
Questions about Segway-Ninebot Grade 10.9 structural screw (part 10.01.3188.00) screws
- What size screw does Segway-Ninebot Grade 10.9 structural screw (part 10.01.3188.00) use?
- M4 × 16 mm for hex socket cylindrical head, galvanised carbon steel, drop-resistance rated.
- How long are the screws in Segway-Ninebot Grade 10.9 structural screw (part 10.01.3188.00)?
- The record gives 16 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Segway-Ninebot Grade 10.9 structural screw (part 10.01.3188.00)?
- The source lists a Hex socket (Allen) drive. Standard M4 heads otherwise take PH2 (Phillips) or T20 (Torx), or a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.