How long are the screws in Segway Ninebot Max G30 dashboard cover?

The record gives 8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.

What is the thread pitch of an M3 screw?

0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.

What screwdriver do I need for Segway Ninebot Max G30 dashboard cover?

The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.

Can I use an imperial screw instead of M3?

No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Segway Ninebot Max G30 dashboard cover?

TechSpareWarehouse (our own store) lists M3 x 8mm, which matches the length in the records above.

Segway Ninebot Max G30 dashboard cover screw size

M3 · 8 mm long

If you are replacing a screw on Segway Ninebot Max G30 dashboard cover, the thread is M3, 8 mm long.

Where it is used: replacement part listed as M3 x 8 countersunk dashboard cover screws.

Head and drive, as the source states them: flat / countersunk head.

This entry is marked reported and comes from escootervision.eu.

An M3 screw is 3 mm in diameter with a 0.5 mm pitch, tapped with a 2.5 mm drill; imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.

Segway Ninebot Max G30 dashboard cover screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M3	8 mm	0.5 mm	Flat / countersunk	not stated	Replacement part listed as M3 x 8 countersunk dashboard cover screws	Reported

Fitment records and sources

M38mmreported

Replacement part listed as M3 x 8 countersunk dashboard cover screws

pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10

Source

How to check the screw before you buy

On vehicles and bikes, use the original strength class and finish; outdoor hardware is usually stainless or coated to resist corrosion.
Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: the source describes a countersunk (flat) head, and those are measured overall, from the top of the head to the tip.
The record states 8 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M3

ISO 14581 Torx countersunk screws look like plain countersunk screws but need the right lobe driver; a Phillips bit will chew the head.
M3 (3.0mm, 0.5mm pitch) is not #6-32 UNC (~3.5mm) — they look identical and cross-thread, the single most common PC-building mistake.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Vehicles, Marine & Mobility

ABB Terra DC Wallbox (3-phase UL)Adjustable Picatinny rail threaded insert Adult e-scooters Aftermarket car stereo cage Airgun scope/rail mount replacement screws Alpine Head Units Analogis phono cartridge screw set Arduino UNO / full-size Arduino boards Audio MusiKraft cartridge mounting screw kit Audio MusiKraft cartridge/headshell mounting kit Bar-end plug or bar-end shifter Berkel 330M Slicer carriage/guard fastener

Browse all 171 in Vehicles, Marine & Mobility →

The same screw also fits

Devices whose records share a thread with Segway Ninebot Max G30 dashboard cover, closest length match first.

Fishing reel side plate / frame also M3 × 8 mm
Fishing reel handle retainer also M3 × 8 mm
Third-party Raspberry Pi cases & HAT stacks also M3 × 8 mm
Instrument enclosure base/rear panel screws (Metcase Technomet-Control rack case) also M3 × 8 mm
OpenFlexure Delta Stage also M3 × 8 mm
Eurorack synthesiser case (Intellijel 7U Performance Case Gen 2) also M3 × 8 mm
Diebold Nixdorf DN100 ATM also M3 × 8 mm
Arduino Uno / shield mounting holes also M3 × 8 mm

Questions about Segway Ninebot Max G30 dashboard cover screws

What size screw does Segway Ninebot Max G30 dashboard cover use?: M3 × 8 mm for replacement part listed as M3 x 8 countersunk dashboard cover screws.
How long are the screws in Segway Ninebot Max G30 dashboard cover?: The record gives 8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
What is the thread pitch of an M3 screw?: 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
What screwdriver do I need for Segway Ninebot Max G30 dashboard cover?: The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
Can I use an imperial screw instead of M3?: No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Segway Ninebot Max G30 dashboard cover?: TechSpareWarehouse (our own store) lists M3 x 8mm, which matches the length in the records above.

Heads up: shipping delay