Sennheiser wireless mic battery/locking mechanism (MKH800, SK6000) screw size
M1.4 · 3 mm long
The screws used on Sennheiser wireless mic battery/locking mechanism (MKH800, SK6000) are M1.4, 3 mm long.
The record covers screw M1.4 x 3mm for battery locking mechanism, listed in Sennheiser official spare parts shop.
This entry is marked confirmed and comes from sennprospares.co.uk.
An M1.4 screw is 1.4 mm in diameter with a 0.3 mm pitch, tapped with a 1.1 mm drill; imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
Sennheiser wireless mic battery/locking mechanism (MKH800, SK6000) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | 3 mm | 0.3 mm | not stated | not stated | Screw M1.4 x 3mm for battery locking mechanism, listed in Sennheiser official spare parts shop | Confirmed |
Fitment records and sources
Screw M1.4 x 3mm for battery locking mechanism, listed in Sennheiser official spare parts shop
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- For medical and lab equipment, use the manufacturer's replacement part where one is specified; the thread size here helps identify it, not certify it.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 3 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M1.4 heads take PH000 / PH00 for Phillips and T2–T3 for Torx, and a 1.3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Medical & Laboratory
The same screw also fits
Devices whose records share a thread with Sennheiser wireless mic battery/locking mechanism (MKH800, SK6000), closest length match first.
- Behind-the-ear hearing aid shell also M1.4 × 3 mm
- Dental handpiece cartridge screws also M1.4 × 3 mm
- Bredent dental prosthetic screw also M1.4 × 3 mm
- LG smartphones also M1.4 × 3 mm
- Sennheiser SK6000 / MKH800 battery lock also M1.4 × 3 mm
- Google Pixel phones also M1.4 × 3 mm
- Samsung Galaxy S23+ internal shields also M1.4 × 3 mm
- Moto X Pure Edition phone backplate screw also M1.4 × 3 mm
Questions about Sennheiser wireless mic battery/locking mechanism (MKH800, SK6000) screws
- What size screw does Sennheiser wireless mic battery/locking mechanism (MKH800, SK6000) use?
- M1.4 × 3 mm for screw M1.4 x 3mm for battery locking mechanism, listed in Sennheiser official spare parts shop.
- How long are the screws in Sennheiser wireless mic battery/locking mechanism (MKH800, SK6000)?
- The record gives 3 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for Sennheiser wireless mic battery/locking mechanism (MKH800, SK6000)?
- The sources do not name the drive. For M1.4, Phillips heads normally take PH000 / PH00 and Torx heads T2–T3; socket heads take a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.