Smart lock interior module screw size
M4 · 6 to 12 mm long
The screws used on Smart lock interior module are M4 in lengths from 6 to 12 mm.
It is listed for interior electronics module mounting screws.
This entry is marked reported.
M4 means a 4 mm nominal diameter with a 0.7 mm thread pitch. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Smart lock interior module screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 6–12 mm | 0.7 mm | not stated | not stated | Interior electronics module mounting screws | Reported |
Fitment records and sources
Interior electronics module mounting screws
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Phone and wearable screws are tiny and often differ by fractions of a millimetre between positions; keep each one next to the hole it came from.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 6–12 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Smart doorbell and lock kits bundle metric machine screws with imperial wood screws in the same bag; the metric ones are rarely labelled.
- M4 and 6-32 UNC share a nominal diameter with different pitch — a classic cross-thread in US-market kits.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Phones, Tablets & Wearables
Akuvox A08 video doorbellAkuvox A08 video doorbell (back plate)Anbernic RG35XX rear case screwsApple Watch case screwsApple Watch strap adapterASUS ROG Ally (RC71L)Asus ROG Ally (RC71L) back panel and M.2 2230 SSD coverASUS ROG Ally RC71L rear shellCompact smart sensor PCBsDive watch bezel insertDive watch bezelsExtech 407732 sound level meter battery cover screw
Browse all 134 in Phones, Tablets & Wearables →The same screw also fits
Devices whose records share a thread with Smart lock interior module, closest length match first.
- Tablet / POS dock mounts also M4 × 6–10 mm
- Ring video doorbell mounting hardware also M4 × 6–12 mm
- Dell UZ2315H also M4 × 10 mm
- ASUS AIO M3700WUA/WYA all-in-one PC also M4 × 7 mm
- Dell P2014H also M4 × 10 mm
- Singer / Bernette / EverSewn / Necchi sewing machines also M4 × 6 mm
- Dell U2917W also M4 × 10 mm
- Panasonic TC-L60DT60 also M4 × 10 mm
Questions about Smart lock interior module screws
- What size screw does Smart lock interior module use?
- M4 × 6–12 mm for interior electronics module mounting screws.
- How long are the screws in Smart lock interior module?
- The records range from 6 to 12 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Smart lock interior module?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.