Sony PMW-EX1R camcorder screw size
M1.4 · 2.5 mm long
Sony PMW-EX1R camcorder takes M1.4 metric screws, 2.5 mm long.
It is listed for M1.4 x 2.5mm screws (x2) on a small internal bracket near the lithium battery.
This entry is marked confirmed and comes from engineering-gourmet.wdfiles.com.
For reference, M1.4 is 1.4 mm across the threads at 0.3 mm pitch. The imperial size people confuse it with: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
Sony PMW-EX1R camcorder screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | 2.5 mm | 0.3 mm | not stated | not stated | M1.4 x 2.5mm screws (x2) on a small internal bracket near the lithium battery | Confirmed |
Fitment records and sources
M1.4 x 2.5mm screws (x2) on a small internal bracket near the lithium battery
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 2.5 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M1.4 heads take PH000 / PH00 for Phillips and T2–T3 for Torx, and a 1.3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with Sony PMW-EX1R camcorder, closest length match first.
- Samsung Galaxy M51 (SM-M515F) also M1.4 × 2.5 mm
- Samsung Galaxy S23+ internal shields also M1.4 × 2.5 mm
- Dental handpiece cartridge screws also M1.4 × 2.5 mm
- Behind-the-ear hearing aid shell also M1.4 × 2.5 mm
- DJI Mini 2 gimbal camera arm screws also M1.4 × 2.5 mm
- LG smartphones also M1.4 × 2.5 mm
- Google Pixel phones also M1.4 × 2.5 mm
- Eyeglass hinge screw (internal thread spec) also M1.4 × 2.5 mm
Questions about Sony PMW-EX1R camcorder screws
- What size screw does Sony PMW-EX1R camcorder use?
- M1.4 × 2.5 mm for M1.4 x 2.5mm screws (x2) on a small internal bracket near the lithium battery.
- How long are the screws in Sony PMW-EX1R camcorder?
- The record gives 2.5 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for Sony PMW-EX1R camcorder?
- The sources do not name the drive. For M1.4, Phillips heads normally take PH000 / PH00 and Torx heads T2–T3; socket heads take a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.