Tofu60 mechanical keyboard case screw size
M2 · 4 to 5 mm long
The screws used on Tofu60 mechanical keyboard case are M2 in lengths from 4 to 5 mm.
It is listed for factory case screws are M2 x 4mm, with M2 x 5mm as an alternative.
This entry is marked confirmed and comes from shuntool.com.
For reference, M2 is 2 mm across the threads at 0.4 mm pitch. The imperial size people confuse it with: #2-56 UNC (2.18 mm) is close but not interchangeable.
Tofu60 mechanical keyboard case screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M2 | 4–5 mm | 0.4 mm | not stated | not stated | Factory case screws are M2 x 4mm, with M2 x 5mm as an alternative | Confirmed |
Fitment records and sources
Factory case screws are M2 x 4mm, with M2 x 5mm as an alternative
pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6
How to check the screw before you buy
- Industrial parts lists usually give the full callout (thread, length, head, grade); match all four, not just the thread.
- Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 4–5 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M2
- M2 (2.00mm, 0.4mm pitch) is NOT the same as #2-56 UNC (2.18mm) — close enough to cross-thread and strip if forced.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M2 x 4mm Phillips Wafer Head Machine Screws Black 50-Pack Laptop SSD Repair
$4.49 each · min. 2
-
M2 x 4mm Screws for Dell Latitude 5530 SSD Type-C Bracket 10-Pack Black
$4.99
-
M2 x 5mm Replacement Bottom Case Screws for Dell Inspiron 3535 Laptop 10-Pack
$4.99 -
M2 x 5mm Phillips Wafer Head Screw for Dell G16 7630 Gaming Laptop Repair - Pack of 100 Black
$7.99 -
Dell Latitude 5530 Replacement Screws Sold Individually – M2 x 3mm, M2 x 4mm, M2.5 x 5mm Phillips Wafer Head, Black
$0.10Choose size -
HP EliteBook 840 G8 Replacement Screws Sold Individually – M1.6 x 3mm, M2 x 2.5mm, M2 x 4mm, M2.5 x 4mm Phillips Wafer Head, Black
$0.10Choose size -
Dell Inspiron 15 3520 Replacement Screws Sold Individually – M2 x 3mm, M2 x 5mm, M2.5 x 5mm, M3 x 3mm Phillips Wafer Head, Black
$0.10Choose size
-
Dell Latitude 5430 Replacement Screws Sold Individually – M2 x 2.5mm, M2 x 3mm, M2 x 5mm, M2.5 x 5mm Phillips Wafer Head, Black
$0.10Choose size
More in Industrial & Machinery
ABB ACS580 motor terminal box / cable glandsABB ACS580 terminal hardware (frames R3-R5)ABB random-wound motor terminal boxes (ACS580 drive systems)Allen-Bradley ControlLogix 1756-A chassisAngle grinder gear housingBianchi / Nuova Simonelli / Rheavendors / Saeco vending machineCircular saw blade guard pivotContender Planetary Mixer MXP004/MXP005 (commercial bakery mixer) electrical diagram terminal screwsCordless drill housing shellsCOSEL power supply terminal block (used in industrial/pump/water-treatment control panels)Datalogic DS2400 fixed-mount barcode readerDeWalt D51430 / D51431 pneumatic nailer
Browse all 113 in Industrial & Machinery →The same screw also fits
Devices whose records share a thread with Tofu60 mechanical keyboard case, closest length match first.
- KBDfans Tofu60 case also M2 × 4 mm
- Kadee HO-scale coupler mounting also M2 × 4–5 mm
- Lenovo ThinkPad P51s also M2 × 4 mm
- Lenovo ThinkPad Edge E130 also M2 × 4 mm
- Dell Inspiron 27 7775 Aio also M2 × 4 mm
- Lenovo B50-70 also M2 × 4 mm
- HP Compaq Presario M2000 also M2 × 4 mm
- Lenovo V14 Gen 4 also M2 × 4 mm
Questions about Tofu60 mechanical keyboard case screws
- What size screw does Tofu60 mechanical keyboard case use?
- M2 × 4–5 mm for factory case screws are M2 x 4mm, with M2 x 5mm as an alternative.
- How long are the screws in Tofu60 mechanical keyboard case?
- The records range from 4 to 5 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M2 screw?
- 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
- What screwdriver do I need for Tofu60 mechanical keyboard case?
- The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M2?
- No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Tofu60 mechanical keyboard case?
- TechSpareWarehouse (our own store) lists M2 x 4mm and M2 x 5mm, which match lengths in the records above.