VMAC Multifunction Power System D600007 screw size
M4 / M5 / M6 · 8 to 16 mm long
The screws used on VMAC Multifunction Power System D600007 are M4, M5 and M6 in lengths from 8 to 16 mm.
There are 5 separate fitment records for it, including control box mounting pan head screw PN 1500647 (M4), control panel mount screw PN 1500632 (M5) and solenoid valve mounting screw PN 1500681 (M5), plus 2 more in the table below.
Head and drive, as the sources state them: pan head and Phillips drive.
0 of the 5 records are marked confirmed, drawn from 1 source (vmacair.com).
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
VMAC Multifunction Power System D600007 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 8 mm | 0.7 mm | Pan head | not stated | control box mounting pan head screw PN 1500647 | Reported |
| M5 | 10 mm | 0.8 mm | not stated | not stated | control panel mount screw PN 1500632 | Reported |
| M5 | 14 mm | 0.8 mm | not stated | not stated | solenoid valve mounting screw PN 1500681 | Reported |
| M6 | 12 mm | 1 mm | not stated | not stated | electrical bracket screw M6x1 stainless PN 1500629stainless | Reported |
| M6 | 16 mm | 1 mm | not stated | Phillips | flat Phillips stainless retainer screw PN 1500667stainless | Reported |
Fitment records and sources
control box mounting pan head screw PN 1500647
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
control panel mount screw PN 1500632
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
solenoid valve mounting screw PN 1500681
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
electrical bracket screw M6x1 stainless PN 1500629
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
flat Phillips stainless retainer screw PN 1500667
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- On vehicles and bikes, use the original strength class and finish; outdoor hardware is usually stainless or coated to resist corrosion.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). This device also uses M5 / M6, so measure each screw rather than assuming they match.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for pan head screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The records span 8–16 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source names a Phillips drive. For comparison, standard M4 heads take PH2 (Phillips) or T20 (Torx), or a 3 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4 / M5 / M6
- goBILDA is metric M4; the older Actobotics/ServoCity system it resembles is imperial 6-32. The parts look alike and will strip each other.
- GoPro also uses M5 for its classic two-prong mount thumbscrew and buckle system, while smaller GoPro chassis screws are commonly Torx-driven without a confirmed metric thread in available sources — don't conflate the mount thumbscrew size with internal chassis screws.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M6 x 16mm Black Wafer Head Rack Screws for Rittal DK 7094.100 / 7094.110 / 7094.140 19-inch Rack – 20-Pack Replacement
$8.99Choose size -
M6 x 16mm Black Wafer Head Awning & Box Screws for Thule Awning 326 / 327 / 328, Conduit Box 317 & Xpedition 820 / 821 (50333) – 8-Pack Replacement
$6.99Choose size -
M6 x 12mm Black Wafer Head TV Back-Panel Screws for Vizio VQD65R-1004, VQD70R-1001, VQM55C-1004, VQM65C-1004 – 8-Pack Replacement
$6.99Choose size -
M6 x 12mm Black Wafer Head Brake Line Screws for GOTRAX G3, G4, GMAX & GMAX Ultra – 8-Pack Replacement
$6.99Choose size -
M5 x 10mm Black Wafer Head Bike Fender & Rack Screws for Tern MTR Fenders, Blackburn EX-1 Rack, ENVO Stax & René Herse Fender Set – 10-Pack Replacement
$5.99Choose size -
M5 x 10mm Black Wafer Head Folding Mechanism Screws for GOTRAX GXL V2, Rival, XR Ultra & XR Elite – 10-Pack Replacement
$5.99Choose size
More in Vehicles, Marine & Mobility
The same screw also fits
Devices whose records share a thread with VMAC Multifunction Power System D600007, closest length match first.
- Bicycle bottle cage bosses (near universal) also M5 × 14 mm
- Pride Go-Go scooter tiller lock knob also M6 × 16 mm
- Motorcycle side panels and tail cowl also M6 × 12 mm
- Motorcycle windscreen also M5 × 14 mm
- Thule Rapid Podium Foot Pack 460R also M6 × 16 mm
- IPS Group M5 Single-Space Smart Parking Meter mechanism retrofit module also M4 × 8 mm
- Small boat deck hardware also M6 × 16 mm
- Motorcycle fairing panels also M6 × 12 mm
Questions about VMAC Multifunction Power System D600007 screws
- What size screw does VMAC Multifunction Power System D600007 use?
- M4 × 8 mm for control box mounting pan head screw PN 1500647; M5 × 10 mm for control panel mount screw PN 1500632; M5 × 14 mm for solenoid valve mounting screw PN 1500681; M6 × 12 mm for electrical bracket screw M6x1 stainless PN 1500629; M6 × 16 mm for flat Phillips stainless retainer screw PN 1500667.
- How long are the screws in VMAC Multifunction Power System D600007?
- The records range from 8 to 16 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for VMAC Multifunction Power System D600007?
- The source lists a Phillips drive. Standard M4 heads otherwise take PH2 (Phillips) or T20 (Torx), or a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.