Vulcan-Hart Chef combi oven 61E/101E screw size
M4 · 10 mm long
If you are replacing a screw on Vulcan-Hart Chef combi oven 61E/101E, the thread is M4, 10 mm long.
Where it is used: A2 stainless TCHC ISO 4762 door hinge/panel screw.
Head and drive, as the source states them: socket cap head.
This entry is marked confirmed and comes from webstaurantstore.com.
For reference, M4 is 4 mm across the threads at 0.7 mm pitch. The imperial size people confuse it with: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Vulcan-Hart Chef combi oven 61E/101E screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 10 mm | 0.7 mm | Socket cap | not stated | A2 stainless TCHC ISO 4762 door hinge/panel screwstainless | Confirmed |
Fitment records and sources
A2 stainless TCHC ISO 4762 door hinge/panel screw
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Appliance panels often use self-tapping screws into sheet metal or plastic, and machine screws into nuts or inserts — keep each type where it came from.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for socket cap screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The record states 10 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Most HVAC chassis hardware in US-market units is imperial; metric shows up mainly on European-made components.
- M4 and 6-32 UNC share a nominal diameter with different pitch — a classic cross-thread in US-market kits.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Appliances & HVAC
The same screw also fits
Devices whose records share a thread with Vulcan-Hart Chef combi oven 61E/101E, closest length match first.
- Refrigerator kick plate grille also M4 × 10 mm
- Faucet escutcheon / cover plates also M4 × 10 mm
- Samsung refrigerator also M4 × 10 mm
- Washer / dryer top panel also M4 × 10 mm
- Espresso machine group head also M4 × 10 mm
- Furrion RV appliance trim kit hardware also M4 × 10 mm
- Dyson vacuum motor housing also M4 × 10 mm
- Drip coffee machine housing also M4 × 10 mm
Questions about Vulcan-Hart Chef combi oven 61E/101E screws
- What size screw does Vulcan-Hart Chef combi oven 61E/101E use?
- M4 × 10 mm for A2 stainless TCHC ISO 4762 door hinge/panel screw.
- How long are the screws in Vulcan-Hart Chef combi oven 61E/101E?
- The record gives 10 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Vulcan-Hart Chef combi oven 61E/101E?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.