WAGO 869-359 / 869-354 rail-mount end terminal block screw size
M4 · length not stated in the sources
If you are replacing a screw on WAGO 869-359 / 869-354 rail-mount end terminal block, the thread is M4. None of the sources we found gives an exact length, so measure the original before you order.
The record covers DIN-rail end stop fixing flange (4.2mm hole).
This entry is marked confirmed and comes from wago.com 869-359 product page.
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
WAGO 869-359 / 869-354 rail-mount end terminal block screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | not stated | 0.7 mm | not stated | not stated | DIN-rail end stop fixing flange (4.2mm hole)washer / flange face | Confirmed |
Fitment records and sources
DIN-rail end stop fixing flange (4.2mm hole)
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
Source: wago.com 869-359 product page
How to check the screw before you buy
- Board standoffs and enclosure bosses set the usable length: the screw should clamp the board without bottoming in the standoff.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Festo sensor brackets are named after the sensor interface (DASP-M4-...), but the bracket's own fixing screws are often a different size (M5/M6/M8).
- There is no single standard Picatinny/rail screw size; makers use metric M3/M4 and imperial 6-48 or 8-40 interchangeably. Always measure the existing screw.
More in Electronics, Racks & Enclosures
19-inch rack cage nut (light equipment)19-inch rack cage nut (metric square-hole rails)19-inch rack cage nut (mid size)19-inch rack cage nut and panel screw19-inch rack network and AV gear19-inch rack-mount audio/AV equipment19-inch server racks19in / 10in server rack cage nut and screw kit19in equipment rack (Kendall Howard cage nuts)19in rack cage nuts (alternate metric)19in rack cage nuts (metric)1U rack-mount PDU (American Denki)
Browse all 357 in Electronics, Racks & Enclosures →The same screw also fits
Devices whose records share a thread with WAGO 869-359 / 869-354 rail-mount end terminal block, closest length match first.
- BYD Battery-Box Premium LVS also M4
- Rackmount KVM chassis also M4
- Refrigerator door handle also M4
- SICK BEF-AP-EPA universal sensor adapter bracket also M4
- Garmin FishFinder 80 flush mount kit also M4
- kvmswitchtech CE-6 / Cat5 IP Matrix rackmount KVM switch also M4
- Sungrow SBP4K8 battery also M4
- Crowcon Xgard Bright fixed gas detector (mining/oil & gas field electronics) also M4
Questions about WAGO 869-359 / 869-354 rail-mount end terminal block screws
- What size screw does WAGO 869-359 / 869-354 rail-mount end terminal block use?
- M4 for DIN-rail end stop fixing flange (4.2mm hole).
- How long are the screws in WAGO 869-359 / 869-354 rail-mount end terminal block?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for WAGO 869-359 / 869-354 rail-mount end terminal block?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.