Windshield ADAS camera bracket screw size
M6 · 8 to 14 mm long
Windshield ADAS camera bracket takes M6 metric screws in lengths from 8 to 14 mm.
The record covers driver-assist camera and sensor brackets.
This entry is marked reported.
An M6 screw is 6 mm in diameter with a 1 mm pitch, tapped with a 5 mm drill; imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Windshield ADAS camera bracket screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 8–14 mm | 1 mm | not stated | not stated | Driver-assist camera and sensor brackets | Reported |
Fitment records and sources
Driver-assist camera and sensor brackets
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Do not confuse metric mounting screws with the 1/4-20 or 3/8-16 tripod threads that cameras and clamps also carry.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 8–14 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- TS-Optics Losmandy-style dovetail bars drill through-holes sized to accept either M6 metric screws or 1/4" imperial screws interchangeably in the same countersunk holes.
- Camera tripods use imperial 1/4-20, which looks like M6 but is a different pitch — forcing one strips the socket.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Cameras & Optics
1.25" eyepiece/diagonal/SCT visual back thumb screwAimpoint Comp M4 / M4s LRP & TNP mountAimpoint Micro T-1/T-2/H-1/H-2 standard mountAimpoint Micro T-1/T-2/H-1/H-2 standard mount screwAimpoint SM-2001/2007 Micro T1/T2 mountAirsoft red dot sight mounting screw set (Laylax/Quintes Sence)Airsoft/firearm red-dot sight optic mounting screws (Vortex Viper, Swampfox patterns)Alpine and touring ski bindings (Binding Freedom inserts)Arca-style quick-release plateARRI plate for Sony VENICE 1/2Artesky 340mm Vixen Dovetail BarAstromania finder scope dovetail base
Browse all 278 in Cameras & Optics →The same screw also fits
Devices whose records share a thread with Windshield ADAS camera bracket, closest length match first.
- Optical breadboard / optical table (metric) also M6 × 8–14 mm
- Cinema camera cheese plates & cages also M6 × 8–12 mm
- Thorlabs MB2090/M aluminum optical breadboard also M6 × 12.7 mm
- M VESA Digital Signage Wallmount also M6 × 10 mm
- VESA MIS-E/F display mount (200mm+) also M6 × 10–14 mm
- MTD / Cub Cadet / Troy-Bilt two-stage snow blower also M6 × 12 mm
- 19-inch rack cage nut (metric square-hole rails) also M6 × 12–14 mm
- Electrolux Professional compact rack-type dishwasher also M6 × 14 mm
Questions about Windshield ADAS camera bracket screws
- What size screw does Windshield ADAS camera bracket use?
- M6 × 8–14 mm for driver-assist camera and sensor brackets.
- How long are the screws in Windshield ADAS camera bracket?
- The records range from 8 to 14 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Windshield ADAS camera bracket?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.