Xbox Series X PSU bracket screw size
M3 · 8 to 10 mm long
Our records put Xbox Series X PSU bracket on M3 screws in lengths from 8 to 10 mm.
It is listed for power supply bracket retention, Torx.
Head and drive, as the source states them: Torx T8 drive.
This entry is marked reported and comes from ifixit.com.
An M3 screw is 3 mm in diameter with a 0.5 mm pitch, tapped with a 2.5 mm drill; imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
Xbox Series X PSU bracket screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | 8–10 mm | 0.5 mm | not stated | Torx T8 | Power supply bracket retention, Torx | Reported |
Fitment records and sources
Power supply bracket retention, Torx
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Over-long screws in phones are a known cause of damaged boards (Apple's 'long screw damage'), so never swap positions.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 8–10 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source names a Torx T8 drive. For comparison, standard M3 heads take PH1 (Phillips) or T10 (Torx), or a 2.5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3
- Power-tool gearcase and clamshell screws are usually thread-forming (marked "ST") even when the parts list gives an M-size — a normal machine screw of the same size may not hold in the plastic boss.
- LED strip clips strip easily — M3x12 into thin plastic should be hand-driven, never with a power driver.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M3 x 8mm Screws for Leather Spike Attachments Guitar Straps 10-Pack
$4.99 -
M3 x 8mm Phillips Wafer Head Screw for SLA Resin 3D Printer VAT Film - Single Replacement Black
$0.10 each · min. 50
-
M3 x 10mm Phillips Wafer Head Screw for Sim Racing Wheel Paddle Shifter - Single Replacement Black
$0.10 each · min. 50
-
M3 x 10mm Phillips Wafer Head Screw for RC Car/Truck Chassis Mount - Single Replacement Black
$0.10 each · min. 50
-
M3 x 8mm Phillips Flat Head Countersunk Machine Screws Zinc Silver 100-Pack for RC & 3D Printers
$9.99 -
M3 x 8mm Phillips Flat Head Countersunk Machine Screws Zinc Silver 10-Pack for RC & 3D Printers
$4.99 -
M3 x 10mm Phillips Wafer Head Screw for 3D Printer Frame Assembly - Single Replacement Black
$0.10 each · min. 50
More in Phones, Tablets & Wearables
Akuvox A08 video doorbellAkuvox A08 video doorbell (back plate)Anbernic RG35XX rear case screwsApple Watch case screwsApple Watch strap adapterASUS ROG Ally (RC71L)Asus ROG Ally (RC71L) back panel and M.2 2230 SSD coverASUS ROG Ally RC71L rear shellCompact smart sensor PCBsDive watch bezel insertDive watch bezelsExtech 407732 sound level meter battery cover screw
Browse all 134 in Phones, Tablets & Wearables →The same screw also fits
Devices whose records share a thread with Xbox Series X PSU bracket, closest length match first.
- PlayStation 5 disc drive and shell also M3 × 8–10 mm
- Smart home sensor brackets also M3 × 8–10 mm
- Xbox Series S internal chassis also M3 × 8–10 mm
- Bambu Lab X1 / P1 / A1 frame and toolhead also M3 × 8–10 mm
- Lenovo ThinkPad 765L also M3 × 8 mm
- Dell U2419HC also M3 × 8 mm
- Elo self-service stand (E796965 / E797162) also M3 × 8 mm
- Fishing reel handle retainer also M3 × 8–10 mm
Questions about Xbox Series X PSU bracket screws
- What size screw does Xbox Series X PSU bracket use?
- M3 × 8–10 mm for power supply bracket retention, Torx.
- How long are the screws in Xbox Series X PSU bracket?
- The records range from 8 to 10 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for Xbox Series X PSU bracket?
- The source lists a Torx T8 drive. Standard M3 heads otherwise take PH1 (Phillips) or T10 (Torx), or a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Xbox Series X PSU bracket?
- TechSpareWarehouse (our own store) lists M3 x 8mm and M3 x 10mm, which match lengths in the records above.