Zeiss camera lens focus scale screw screw size
M1.4 · 2 mm long
Zeiss camera lens focus scale screw takes M1.4 metric screws, 2 mm long.
The record covers genuine Zeiss factory screw pack explicitly listed as thread M1.4, length 2mm, slotted drive, used on Zeiss Super Speed focus scale.
Head and drive, as the source states them: Slotted drive.
This entry is marked confirmed and comes from parts.ducloslenses.com.
M1.4 means a 1.4 mm nominal diameter with a 0.3 mm thread pitch. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
Zeiss camera lens focus scale screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | 2 mm | 0.3 mm | not stated | Slotted | Genuine Zeiss factory screw pack explicitly listed as thread M1.4, length 2mm, slotted drive, used on Zeiss Super Speed focus scale | Confirmed |
Fitment records and sources
Genuine Zeiss factory screw pack explicitly listed as thread M1.4, length 2mm, slotted drive, used on Zeiss Super Speed focus scale
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- Do not confuse metric mounting screws with the 1/4-20 or 3/8-16 tripod threads that cameras and clamps also carry.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 2 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Slotted drive. For comparison, standard M1.4 heads take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- iPhone-series OEM screws use both 'Main Screw' and 'Super Screw' names for M1.4 fasteners with different lengths per model/position — always match by dimensional code (L x D x T), not just model name.
- Whoop drone M1.4 comes in steel, PEEK and RENY versions: plastic ones are for cameras, not structural frame use.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Cameras & Optics
The same screw also fits
Devices whose records share a thread with Zeiss camera lens focus scale screw, closest length match first.
- Vintage Japanese camera lens mounts (mixed brands) also M1.4 × 2 mm
- Compact & action cameras also M1.4 × 2 mm
- Eyeglass hinge screw (the most common size) also M1.4 × 2 mm
- Oakley O Matter / steel frame hinge also M1.4 × 2 mm
- Ultrabook display bezel also M1.4 × 2 mm
- Behind-the-ear hearing aid shell also M1.4 × 2 mm
- Dell Pro Max 16 Premium MA16250 also M1.4 × 2 mm
- Dell XPS 14 9440 also M1.4 × 2 mm
Questions about Zeiss camera lens focus scale screw screws
- What size screw does Zeiss camera lens focus scale screw use?
- M1.4 × 2 mm for genuine Zeiss factory screw pack explicitly listed as thread M1.4, length 2mm, slotted drive, used on Zeiss Super Speed focus scale.
- How long are the screws in Zeiss camera lens focus scale screw?
- The record gives 2 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for Zeiss camera lens focus scale screw?
- The source lists a Slotted drive. Standard M1.4 heads otherwise take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Zeiss camera lens focus scale screw?
- TechSpareWarehouse (our own store) lists M1.4 x 2mm, which matches the length in the records above.