Acer Predator X34 screw size
M4 · 8 to 10 mm long
The screws used on Acer Predator X34 are M4 in lengths from 8 to 10 mm.
There are 3 separate fitment records for it, including stand (qty 4) (M4), vesa mount (qty 4) (M4) and vesa mount (qty 4) (M4).
3 of the 3 records are marked confirmed, drawn from 1 source (global-download.acer.com).
M4 means a 4 mm nominal diameter with a 0.7 mm thread pitch. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Acer Predator X34 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 10 mm | 0.7 mm | not stated | not stated | Stand (qty 4) | Confirmed |
| M4 | 10 mm | 0.7 mm | not stated | not stated | Vesa mount (qty 4) | Confirmed |
| M4 | 8 mm | 0.7 mm | not stated | not stated | Vesa mount (qty 4) | Confirmed |
Fitment records and sources
Stand (qty 4)
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
Vesa mount (qty 4)
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
Vesa mount (qty 4)
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 8–10 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Dashcam mounts advertised as '1/4" M4 screw joint' have two different threads: the 1/4"-20 camera thread and a separate M4 grub screw for the ball joint — don't order the wrong one.
- VESA fixes the hole pattern and max thread depth, not screw length — length depends on the panel back and any spacers.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Displays, TVs & Mounts
The same screw also fits
Devices whose records share a thread with Acer Predator X34, closest length match first.
- Dell P2418HT also M4 × 10 mm
- ASUS BE27ACSBK also M4 × 10 mm
- Dell UltraSharp 22-27in monitors also M4 × 10 mm
- Dell U3419W also M4 × 10 mm
- Dell U3415W also M4 × 10 mm
- Dell P2719HC also M4 × 10 mm
- ASUS VG27AQA1A also M4 × 10 mm
- Dell U2718QM also M4 × 10 mm
Questions about Acer Predator X34 screws
- What size screw does Acer Predator X34 use?
- M4 × 10 mm for stand (qty 4); M4 × 10 mm for vesa mount (qty 4); M4 × 8 mm for vesa mount (qty 4).
- How long are the screws in Acer Predator X34?
- The records range from 8 to 10 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Acer Predator X34?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.