Apple HomePod internal drivers screw size
M3 · 6 to 10 mm long
The screws used on Apple HomePod internal drivers are M3 in lengths from 6 to 10 mm.
It is listed for torx/Phillips screws on internal driver mounts.
Head and drive, as the source states them: Torx drive.
This entry is marked reported and comes from ifixit.com.
An M3 screw is 3 mm in diameter with a 0.5 mm pitch, tapped with a 2.5 mm drill; imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
Apple HomePod internal drivers screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | 6–10 mm | 0.5 mm | not stated | Torx | Torx/Phillips screws on internal driver mounts | Reported |
Fitment records and sources
Torx/Phillips screws on internal driver mounts
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 6–10 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source names a Torx drive. For comparison, standard M3 heads take PH1 (Phillips) or T10 (Torx), or a 2.5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3
- Sonos speakers mix lengths within one unit — M3 for driver housings, M2.5 at the control panel. Keep them sorted during teardown.
- Telescope thumbscrews are sold in a wide non-metric legacy range too (1/4-20, 8-32, 10-32 on many Meade/Celestron mounts), so metric M3/M4 fitment applies mainly to newer/international accessory ecosystems (SkyWatcher, generic 1.25" accessories) and should not be assumed universal.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M3 x 6mm Replacement Screws for XLR Audio Connectors Phillips Wafer Head 50-Pack
$4.99 -
M3 x 6mm Phillips Wafer Head Carbon Steel Machine Screws for XLR Audio Connectors | 50-Pack (Black)
$4.99
-
M3 x 8mm Screws for Leather Spike Attachments Guitar Straps 10-Pack
$4.99 -
M3 x 8mm Phillips Wafer Head Screw for SLA Resin 3D Printer VAT Film - Single Replacement Black
$0.10 each · min. 50
-
M3 x 10mm Phillips Wafer Head Screw for Sim Racing Wheel Paddle Shifter - Single Replacement Black
$0.10 each · min. 50
-
M3 x 10mm Phillips Wafer Head Screw for RC Car/Truck Chassis Mount - Single Replacement Black
$0.10 each · min. 50
-
M3 x 6mm Phillips Wafer Head Screw for 3D Printer Frame Assembly - Single Replacement Black
$0.10 each · min. 50
-
M3 x 6mm Phillips Wafer Head Screw for Boutique Guitar Pedal Enclosure - Single Replacement Black
$0.10 each · min. 50
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with Apple HomePod internal drivers, closest length match first.
- Dell U2917W also M3 × 6 mm
- Dell P2014H also M3 × 6 mm
- Dell UZ2315H also M3 × 6 mm
- Dell Pro 27 Plus monitor (P2725D/DE/QE) also M3 × 6 mm
- Dell SP2318H also M3 × 6 mm
- Philips IntelliVue MP40/MP50 Patient Monitors also M3 × 8 mm
- Dell P2016 also M3 × 6 mm
- HP P24h G4 also M3 × 6 mm
Questions about Apple HomePod internal drivers screws
- What size screw does Apple HomePod internal drivers use?
- M3 × 6–10 mm for torx/Phillips screws on internal driver mounts.
- How long are the screws in Apple HomePod internal drivers?
- The records range from 6 to 10 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for Apple HomePod internal drivers?
- The source lists a Torx drive. Standard M3 heads otherwise take PH1 (Phillips) or T10 (Torx), or a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Apple HomePod internal drivers?
- TechSpareWarehouse (our own store) lists M3 x 6mm, M3 x 8mm and M3 x 10mm, which match lengths in the records above.