ARRI rosette accessory adapter screw size
M3 · length not stated in the sources
ARRI rosette accessory adapter takes M3 metric screws. None of the sources we found gives an exact length, so measure the original before you order.
It is listed for M3 threads on 31.8mm ARRI-standard rosette handgrip adapters.
This entry is marked confirmed and comes from blk.gr.
M3 means a 3 mm nominal diameter with a 0.5 mm thread pitch. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
ARRI rosette accessory adapter screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | not stated | 0.5 mm | not stated | not stated | M3 threads on 31.8mm ARRI-standard rosette handgrip adapters | Confirmed |
Fitment records and sources
M3 threads on 31.8mm ARRI-standard rosette handgrip adapters
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- If several screws hold the same part, check that they are all the same length before assuming they are.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3
- GoPro's own official Dive Housing user guide does not itself state a metric screw size for the housing body; only third-party accessory manufacturer (INON) manuals explicitly cite M6 screws for their add-on arms/adapters attaching to the housing.
- Eurorack is a strong known case with two competing metric standards (M2.5 for Vector rails, M3 for Schroff/DIN-style and 3U threaded rails); mixing rail types requires matching screw/nut thread.
More in Standards & References
2.5in SATA SSD / HDDABB REX640 protection & control relayAgilent (HP) 8453 UV-Visible Spectroscopy SystemAirsoft AEG Version 2 / EHPA gearbox shellBalisong / butterfly knife pivot (aftermarket, ISO 14583 pan head)Beckhoff AMP8x3x distributed servo drive flange mountingBeckhoff AMP8x4x distributed servo drive flange mountingCanadian Solar standard PV modulesCubeSat Kit solar panel clips and chassisDIN 912 socket-head cap screwDIN 912 socket-head cap screw (smallest size)DIN 965 / ISO 7046 countersunk Phillips screw
Browse all 31 in Standards & References →The same screw also fits
Devices whose records share a thread with ARRI rosette accessory adapter, closest length match first.
- 2.5in SATA SSD / HDD also M3
- NBK cleanroom/semiconductor vented socket head cap screw (SVSHT-M3-SD) also M3
- Airsoft AEG Version 2 / EHPA gearbox shell also M3
- Generic hex socket button head screw (ISO 7380-1) also M3
- TO-220 / TO-247 power semiconductor heatsink mounting also M3
- Renishaw CMM stylus (TP1, TP6, SP25M probes) also M3
- DIN 965 / ISO 7046 countersunk Phillips screw also M3
- DIN 912 socket-head cap screw also M3
Questions about ARRI rosette accessory adapter screws
- What size screw does ARRI rosette accessory adapter use?
- M3 for M3 threads on 31.8mm ARRI-standard rosette handgrip adapters.
- How long are the screws in ARRI rosette accessory adapter?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for ARRI rosette accessory adapter?
- The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.