How long are the screws in DIN 912 socket-head cap screw (smallest size)?

The records range from 2 to 10 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M1.4 screw?

0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.

What screwdriver do I need for DIN 912 socket-head cap screw (smallest size)?

The source lists a Hex socket (Allen) drive. Standard M1.4 heads otherwise take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.

Can I use an imperial screw instead of M1.4?

No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for DIN 912 socket-head cap screw (smallest size)?

TechSpareWarehouse (our own store) lists M1.4 x 2mm, which matches the length in the records above.

DIN 912 socket-head cap screw (smallest size) screw size

M1.4 · 2 to 10 mm long

If you are replacing a screw on DIN 912 socket-head cap screw (smallest size), the thread is M1.4 in lengths from 2 to 10 mm.

Where it is used: smallest common DIN 912 SHCS: 0.30mm pitch, head 2.46-2.74mm — useful when matching a tiny hex-drive screw.

Head and drive, as the source states them: socket cap head and Hex socket (Allen) drive.

This entry is marked confirmed and comes from boltport.com.

An M1.4 screw is 1.4 mm in diameter with a 0.3 mm pitch, tapped with a 1.1 mm drill; imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.

DIN 912 socket-head cap screw (smallest size) screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M1.4	2–10 mm	0.3 mm	Socket cap	Hex socket (Allen)	Smallest common DIN 912 SHCS: 0.30mm pitch, head 2.46-2.74mm — useful when matching a tiny hex-drive screw	Confirmed

Fitment records and sources

M1.42-10mmconfirmed

Smallest common DIN 912 SHCS: 0.30mm pitch, head 2.46-2.74mm — useful when matching a tiny hex-drive screw

pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3

Source

How to check the screw before you buy

Take one original screw out first and measure it before ordering; the record above tells you the thread, the original screw tells you the exact length and head.
Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: for socket cap screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
The records span 2–10 mm, which means different positions take different lengths — match each hole to its own screw.
Driver: the source names a Hex socket (Allen) drive. For comparison, standard M1.4 heads take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M1.4

M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Standards & References

2.5in SATA SSD / HDD ABB REX640 protection & control relay Agilent (HP) 8453 UV-Visible Spectroscopy System Airsoft AEG Version 2 / EHPA gearbox shell ARRI rosette accessory adapter Balisong / butterfly knife pivot (aftermarket, ISO 14583 pan head)Beckhoff AMP8x3x distributed servo drive flange mounting Beckhoff AMP8x4x distributed servo drive flange mounting Canadian Solar standard PV modules CubeSat Kit solar panel clips and chassis DIN 912 socket-head cap screw DIN 965 / ISO 7046 countersunk Phillips screw

Browse all 31 in Standards & References →

The same screw also fits

Devices whose records share a thread with DIN 912 socket-head cap screw (smallest size), closest length match first.

Nokia Lumia 1020 internal chassis screw also M1.4 × 3 mm
Samsung Galaxy Watch 3 (45mm) screw also M1.4 × 4 mm
Tantalum/tungsten high-temp pan head screw (77039-1403) also M1.4 × 3 mm
Eyewire / hinge screw, large head (QTE Vigor 80086) also M1.4 × 3.8 mm
HP OmniBook 7 14 inch AI PC: 14- fr0xxx also M1.4 × 2.5 mm
Dell XPS 13 9300 also M1.4 × 4 mm
Dell XPS 13 9345 also M1.4 × 2 mm
Dell XPS 13 9340 also M1.4 × 2 mm

Questions about DIN 912 socket-head cap screw (smallest size) screws

What size screw does DIN 912 socket-head cap screw (smallest size) use?: M1.4 × 2–10 mm for smallest common DIN 912 SHCS: 0.30mm pitch, head 2.46-2.74mm — useful when matching a tiny hex-drive screw.
How long are the screws in DIN 912 socket-head cap screw (smallest size)?: The records range from 2 to 10 mm depending on the position, so match each screw to its own hole.
What is the thread pitch of an M1.4 screw?: 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
What screwdriver do I need for DIN 912 socket-head cap screw (smallest size)?: The source lists a Hex socket (Allen) drive. Standard M1.4 heads otherwise take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
Can I use an imperial screw instead of M1.4?: No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for DIN 912 socket-head cap screw (smallest size)?: TechSpareWarehouse (our own store) lists M1.4 x 2mm, which matches the length in the records above.

Heads up: shipping delay