Banner SXA-MBK laser scanner angle adjustment bracket screw size
M5 · length not stated in the sources
Our records put Banner SXA-MBK laser scanner angle adjustment bracket on M5 screws. None of the sources we found gives an exact length, so measure the original before you order.
The record covers datasheet instructs: 'Provide two M5 holes with 73 mm spacing on the intended wall or mounting surface. The M5 UNI 5933 screws used for mounting the brackets to a wall are not supplied.'.
This entry is marked confirmed and comes from datasheet.sic-components.com.
M5 means a 5 mm nominal diameter with a 0.8 mm thread pitch. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Banner SXA-MBK laser scanner angle adjustment bracket screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | not stated | 0.8 mm | not stated | not stated | Datasheet instructs: 'Provide two M5 holes with 73 mm spacing on the intended wall or mounting surface. The M5 UNI 5933 screws used for mounting the brackets to a wall are not supplied.' | Confirmed |
Fitment records and sources
Datasheet instructs: 'Provide two M5 holes with 73 mm spacing on the intended wall or mounting surface. The M5 UNI 5933 screws used for mounting the brackets to a wall are not supplied.'
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- APC Easy PDU rack-mount screws are self-tapping M5x10, intended for the PDU's own mounting brackets rather than standard rack cage-nut threads.
- M5x0.8 is the de facto universal bike thread — confirm 0.8mm pitch before threading into carbon or alloy bosses.
More in Electronics, Racks & Enclosures
The same screw also fits
Devices whose records share a thread with Banner SXA-MBK laser scanner angle adjustment bracket, closest length match first.
- Vertical trolley 48V 280Ah battery enclosure casters also M5
- Marine swivel mount brackets also M5
- Eurorack rail end-fixing screws (Vector rails, metric variant) also M5
- 19in equipment rack (Kendall Howard cage nuts) also M5
- E-scooter front fork axle bracket also M5
- Kendall Howard universal rack rails also M5
- RV appliance and vent fan brackets also M5
- Tent frame hub connectors also M5
Questions about Banner SXA-MBK laser scanner angle adjustment bracket screws
- What size screw does Banner SXA-MBK laser scanner angle adjustment bracket use?
- M5 for datasheet instructs: 'Provide two M5 holes with 73 mm spacing on the intended wall or mounting surface. The M5 UNI 5933 screws used for mounting the brackets to a wall are not supplied.'.
- How long are the screws in Banner SXA-MBK laser scanner angle adjustment bracket?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Banner SXA-MBK laser scanner angle adjustment bracket?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.