Eurorack rail end-fixing screws (Vector rails, metric variant) screw size
M5 · length not stated in the sources
Eurorack rail end-fixing screws (Vector rails, metric variant) takes M5 metric screws. None of the sources we found gives an exact length, so measure the original before you order.
It is listed for 'The rails can be end fixed using M5 machine screws, although, being of US origin the stated size is 10-32inch' — explicit metric alternative given for Vector rail end fixing.
This entry is marked reported and comes from synthracks.com.
For reference, M5 is 5 mm across the threads at 0.8 mm pitch. The imperial size people confuse it with: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Eurorack rail end-fixing screws (Vector rails, metric variant) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | not stated | 0.8 mm | not stated | not stated | 'The rails can be end fixed using M5 machine screws, although, being of US origin the stated size is 10-32inch' — explicit metric alternative given for Vector rail end fixing | Reported |
Fitment records and sources
'The rails can be end fixed using M5 machine screws, although, being of US origin the stated size is 10-32inch' — explicit metric alternative given for Vector rail end fixing
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- Rack and enclosure hardware mixes metric and imperial (#8-32, #10-32, #6-32), so confirm the thread before forcing a screw.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- Concept2 rowers/ergs look metric-friendly but use imperial 1/4-20 hardware throughout — M6 will NOT thread in; do not force it.
- Rosemount and similar field instruments quote hex driver sizes in inches (e.g. 5/64 in) rather than a metric thread.
More in Electronics, Racks & Enclosures
The same screw also fits
Devices whose records share a thread with Eurorack rail end-fixing screws (Vector rails, metric variant), closest length match first.
- Marine swivel mount brackets also M5
- Vertical trolley 48V 280Ah battery enclosure casters also M5
- Banner SXA-MBK laser scanner angle adjustment bracket also M5
- 19in equipment rack (Kendall Howard cage nuts) also M5
- Kendall Howard universal rack rails also M5
- E-scooter front fork axle bracket also M5
- Hospital bed siderail and actuator brackets also M5
- Pioneer Head Units also M5
Questions about Eurorack rail end-fixing screws (Vector rails, metric variant) screws
- What size screw does Eurorack rail end-fixing screws (Vector rails, metric variant) use?
- M5 for 'The rails can be end fixed using M5 machine screws, although, being of US origin the stated size is 10-32inch' — explicit metric alternative given for Vector rail end fixing.
- How long are the screws in Eurorack rail end-fixing screws (Vector rails, metric variant)?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Eurorack rail end-fixing screws (Vector rails, metric variant)?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.