Carbide3D proximity switch upgrade kit screw size
M3 · length not stated in the sources
Our records put Carbide3D proximity switch upgrade kit on M3 screws. None of the sources we found gives an exact length, so measure the original before you order.
It is listed for assembly guide lists M3 screws for mounting proximity switch brackets.
This entry is marked reported and comes from my.carbide3d.com.
M3 means a 3 mm nominal diameter with a 0.5 mm thread pitch. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
Carbide3D proximity switch upgrade kit screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | not stated | 0.5 mm | not stated | not stated | Assembly guide lists M3 screws for mounting proximity switch brackets | Reported |
Fitment records and sources
Assembly guide lists M3 screws for mounting proximity switch brackets
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- Into printed plastic, the screw either self-taps or needs a heat-set insert; machine screws straight into plastic strip easily.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3
- GoPro's own official Dive Housing user guide does not itself state a metric screw size for the housing body; only third-party accessory manufacturer (INON) manuals explicitly cite M6 screws for their add-on arms/adapters attaching to the housing.
- Pond/aquarium equipment manuals aimed at consumers rarely specify exact thread pitch or length for internal fasteners, since these are considered non-user-serviceable; distributor-level assembly/service manuals (e.g., Maytronics internal documents) are a better source than end-user guides.
More in 3D Printing, CNC & Robotics
2020 extrusion T-nuts (light duty)2020 extrusion T-nuts (standard)2020 T-slot hammer head bolts2020/2040 extrusion end tap2040 extrusion T-nuts3030 extrusion T-nuts (heavy duty)3030/4040 extrusion end tap3D printer & CNC enclosures3D printer hotend to X-carriageActobotics servo horn / hubArduino Mega 2560 mounting holesArduino shield stacking standoffs
Browse all 149 in 3D Printing, CNC & Robotics →The same screw also fits
Devices whose records share a thread with Carbide3D proximity switch upgrade kit, closest length match first.
- ESP32 DevKit boards also M3
- Prusa MK4 / MK4S kit also M3
- Arduino Mega 2560 mounting holes also M3
- Prusa MK3S/MK3.5 to MK4 upgrade kit also M3
- Ender 3 V2 hotend and hotend cover also M3
- Original Prusa MK4 3D printer also M3
- NEMA 23 stepper motor, 3A variant also M3
- Arduino Uno / Mega mounting holes also M3
Questions about Carbide3D proximity switch upgrade kit screws
- What size screw does Carbide3D proximity switch upgrade kit use?
- M3 for assembly guide lists M3 screws for mounting proximity switch brackets.
- How long are the screws in Carbide3D proximity switch upgrade kit?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for Carbide3D proximity switch upgrade kit?
- The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.