Dell S2319HS screw size
M3 / M4 · 6 to 10 mm long
If you are replacing a screw on Dell S2319HS, the thread is M3 and M4 in lengths from 6 to 10 mm.
There are 2 separate fitment records for it, including stand (M3) and vesa mount (M4).
2 of the 2 records are marked confirmed, drawn from 1 source (downloads.dell.com).
An M3 screw is 3 mm in diameter with a 0.5 mm pitch, tapped with a 2.5 mm drill; imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
Dell S2319HS screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | 6 mm | 0.5 mm | not stated | not stated | Stand | Confirmed |
| M4 | 10 mm | 0.7 mm | not stated | not stated | Vesa mount | Confirmed |
Fitment records and sources
Stand
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
Vesa mount
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). This device also uses M4, so measure each screw rather than assuming they match.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 6–10 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3 / M4
- Server drive caddy screws (Dell, HP) are usually M3 in very short lengths (3-4mm) because they bite into thin sheet metal — they are NOT the 6-32 UNC screws that go into the drive's own side holes.
- Telescope thumbscrews are sold in a wide non-metric legacy range too (1/4-20, 8-32, 10-32 on many Meade/Celestron mounts), so metric M3/M4 fitment applies mainly to newer/international accessory ecosystems (SkyWatcher, generic 1.25" accessories) and should not be assumed universal.
- Dashcam mounts advertised as '1/4" M4 screw joint' have two different threads: the 1/4"-20 camera thread and a separate M4 grub screw for the ball joint — don't order the wrong one.
- VESA thread size is set by pattern class: M4 for 75x75/100x100, M6 or M8 for the big 200mm+ patterns. Check the plate on the back of the display.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M3 x 6mm Replacement Screws for XLR Audio Connectors Phillips Wafer Head 50-Pack
$4.99 -
M3 x 6mm Phillips Wafer Head Carbon Steel Machine Screws for XLR Audio Connectors | 50-Pack (Black)
$4.99
-
M3 x 6mm Phillips Wafer Head Screw for 3D Printer Frame Assembly - Single Replacement Black
$0.10 each · min. 50
-
M3 x 6mm Phillips Wafer Head Screw for Boutique Guitar Pedal Enclosure - Single Replacement Black
$0.10 each · min. 50
-
M4 x 10mm Black Wafer Head Charging Port Screws for GOTRAX G3, G4, GMAX & GMAX Ultra – 10-Pack Replacement
$5.49Choose size -
M4 x 10mm Black Wafer Head Fender Clamp Base Screws for Minoura KODACHI DYK-1R Rear Fender – 8-Pack Replacement
$5.49Choose size
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with Dell S2319HS, closest length match first.
- Dell UP2716D also M3 × 6 mm
- Dell P2416D also M3 × 6 mm
- Dell U3417W also M3 × 6 mm
- Dell UP2516D also M3 × 6 mm
- Dell U2417HWI also M3 × 6 mm
- Dell U2718Q also M3 × 6 mm
- Dell P2415Q also M3 × 6 mm
- Dell P2312H also M3 × 6 mm
Questions about Dell S2319HS screws
- What size screw does Dell S2319HS use?
- M3 × 6 mm for stand; M4 × 10 mm for vesa mount.
- How long are the screws in Dell S2319HS?
- The records range from 6 to 10 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for Dell S2319HS?
- The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
- Where can I buy replacement screws for Dell S2319HS?
- TechSpareWarehouse (our own store) lists M3 x 6mm, which matches the length in the records above.