Dell UltraSharp U2725QE monitor screw size

Dell UltraSharp U2725QE monitor screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

How to check the screw before you buy

1. For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
2. Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). This device also uses M3 / M4, so measure each screw rather than assuming they match.
3. Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
4. Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
5. The records span 3–10 mm, which means different positions take different lengths — match each hole to its own screw.
6. Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
7. Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Pitch gauge · Screw size finder · Torque guide

More in Displays, TVs & Mounts

The same screw also fits

Devices whose records share a thread with Dell UltraSharp U2725QE monitor, closest length match first.

• Dell P2017H also M3 × 6 mm
• Dell P2412H also M3 × 6 mm
• Dell P2417H also M3 × 6 mm
• Dell U3818DW also M3 × 6 mm
• Dell U2713HM also M4 × 10 mm
• Dell P2317HWH also M3 × 6 mm
• Dell P2414H also M3 × 6 mm
• Dell UZ2715H also M3 × 6 mm

Questions about Dell UltraSharp U2725QE monitor screws

What size screw does Dell UltraSharp U2725QE monitor use?

M2 × 3.3 mm for keypad board to upper back cover (2); M3 × 5 mm for I/O cover to main chassis (4); M3 × 6 mm for quick accessory port to middle frame (4); M3 × 3 mm for iron cover / USB board to QAP back cover; M3 × 3 mm for main chassis to display panel (4); M3 × 4–5 mm for middle frame to panel (11 + 5); M3 × 6 mm for mylar sheet retention to power boards; M3 × 6 mm for main board and power board mounting (6); M4 × 10 mm for upper back cover to chassis (4); M4 × 8 mm for main/power board ground point.

How long are the screws in Dell UltraSharp U2725QE monitor?

The records range from 3 to 10 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for Dell UltraSharp U2725QE monitor?

The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Dell UltraSharp U2725QE monitor?

TechSpareWarehouse (our own store) lists M3 x 5mm, M3 x 6mm and M3 x 3mm, which match lengths in the records above.