What size screw does Dell XPS 15 9575 2-in-1 use?

M2 × 2–3 mm for base cover perimeter screws.

How long are the screws in Dell XPS 15 9575 2-in-1?

The records range from 2 to 3 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M2 screw?

0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.

What screwdriver do I need for Dell XPS 15 9575 2-in-1?

The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.

Can I use an imperial screw instead of M2?

No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Dell XPS 15 9575 2-in-1?

TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 2.5mm and M2 x 3mm, which match lengths in the records above.

Dell XPS 15 9575 2-in-1 screw size

M2 · 2 to 3 mm long

Our records put Dell XPS 15 9575 2-in-1 on M2 screws in lengths from 2 to 3 mm.

The record covers base cover perimeter screws.

This entry is marked reported and comes from ifixit.com.

For reference, M2 is 2 mm across the threads at 0.4 mm pitch. The imperial size people confuse it with: #2-56 UNC (2.18 mm) is close but not interchangeable.

Dell XPS 15 9575 2-in-1 screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M2	2–3 mm	0.4 mm	not stated	not stated	base cover perimeter screws	Reported

Fitment records and sources

M22-3mmreported

base cover perimeter screws

pitch 0.4 mm · tap 1.6 mm · clearance 2.4 mm · PH0 / Torx T6

Source

How to check the screw before you buy

If several screws hold the same part, check that they are all the same length before assuming they are.
Diameter: across the threads an M2 screw measures about 2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.4 mm from one thread crest to the next (25 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The records span 2–3 mm, which means different positions take different lengths — match each hole to its own screw.
Driver: the source does not name the drive. Standard M2 heads take PH0 for Phillips and T6 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M2 is about 25-40 N·cm into metal threads and 12-20 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M2

M2 (2.00mm, 0.4mm pitch) is NOT the same as #2-56 UNC (2.18mm) — close enough to cross-thread and strip if forced.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Other Equipment

2020 aluminium extrusion T-nuts Acer Aspire / Swift Allen-Bradley PowerFlex 520-series mounting adapter plate Allen-Bradley PowerFlex 750-series Allen-Bradley PowerFlex 750-series I/O shield termination Allen-Bradley PowerFlex 755 IP00 control pod Amiga 500 rear/front case screws (Retro32 replacement set)Arduino Uno / Mega ASUS / MSI / Gigabyte / ASRock motherboards Backscatter FLIP3.1 underwater filter frame screws (2x)Backscatter FLIP3.1 underwater flip-frame retaining screw Bosch Rexroth swivel-in T-slot nut, slot 8

Browse all 125 in Other Equipment →

The same screw also fits

Devices whose records share a thread with Dell XPS 15 9575 2-in-1, closest length match first.

PS5 DualSense controller also M2 × 3 mm
Nintendo Switch also M2 × 2–3 mm
Dell XPS 13 9350 / 9360 / 9365 also M2 × 3 mm
ASUS / MSI / Gigabyte / ASRock motherboards also M2 × 2–3 mm
Nintendo Switch battery shield also M2 × 3 mm
M.2 heatsink / shield assemblies also M2 × 3 mm
TFV12 rebuildable vape tank grub/set screws also M2 × 3 mm
Lenovo B41-30 also M2 × 2 mm

Questions about Dell XPS 15 9575 2-in-1 screws

What size screw does Dell XPS 15 9575 2-in-1 use?: M2 × 2–3 mm for base cover perimeter screws.
How long are the screws in Dell XPS 15 9575 2-in-1?: The records range from 2 to 3 mm depending on the position, so match each screw to its own hole.
What is the thread pitch of an M2 screw?: 0.4 mm (coarse), which is the standard pitch for M2 machine screws; a 0.25 mm fine pitch exists but is uncommon. The tap drill is 1.6 mm and the normal clearance hole is 2.4 mm.
What screwdriver do I need for Dell XPS 15 9575 2-in-1?: The sources do not name the drive. For M2, Phillips heads normally take PH0 and Torx heads T6; socket heads take a 1.5 mm hex key.
Can I use an imperial screw instead of M2?: No. Imperial look-alike: #2-56 UNC (2.18 mm) is close but not interchangeable. Use a true M2 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Dell XPS 15 9575 2-in-1?: TechSpareWarehouse (our own store) lists M2 x 2mm, M2 x 2.5mm and M2 x 3mm, which match lengths in the records above.

Heads up: shipping delay