Allen-Bradley PowerFlex 750-series screw size
M5 · length not stated in the sources
Allen-Bradley PowerFlex 750-series takes M5 metric screws. None of the sources we found gives an exact length, so measure the original before you order.
The record covers ten M5 screws hold the full cabinet options bay guard on frames 8-9, torque 2.8 Nm, 8mm hex.
This entry is marked confirmed and comes from literature.rockwellautomation.com.
For reference, M5 is 5 mm across the threads at 0.8 mm pitch. The imperial size people confuse it with: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Allen-Bradley PowerFlex 750-series screw specifications
One row per fitment record. Head, drive and torque are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Torque | Where it goes | Status |
|---|---|---|---|---|---|---|---|
| M5 | not stated | 0.8 mm | not stated | not stated | 2.8 Nm | Ten M5 screws hold the full cabinet options bay guard on frames 8-9, torque 2.8 Nm, 8mm hex | Confirmed |
Fitment records and sources
Ten M5 screws hold the full cabinet options bay guard on frames 8-9, torque 2.8 Nm, 8mm hex
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- If several screws hold the same part, check that they are all the same length before assuming they are.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Common mix-ups with M5
- Carbon bosses strip easily: 2-4 Nm torque and the right length so the bolt doesn't bottom out.
- Commercial washer-extractor cabinets mix DIN 933 (hex head, full thread) and DIN 84A (slotted pan/cheese head) M5 screws for different panels on the same machine line, so a single family/brand isn't consistent across all fasteners.
More in Other Equipment
The same screw also fits
Devices whose records share a thread with Allen-Bradley PowerFlex 750-series, closest length match first.
- Door lever through-bolts also M5
- Tama percussion / gong bass drum lug (part 7592) also M5
- Eschmann LS5 / SES2555 autoclave also M5
- Victron MultiPlus-II / Quattro-II also M5
- Handlebar accessory clamps also M5
- Flat-pack furniture also M5
- Kestrel e400nb wind turbine also M5
- Euro profile cylinder lock attaching/retaining screw also M5
Questions about Allen-Bradley PowerFlex 750-series screws
- What size screw does Allen-Bradley PowerFlex 750-series use?
- M5 for ten M5 screws hold the full cabinet options bay guard on frames 8-9, torque 2.8 Nm, 8mm hex.
- How long are the screws in Allen-Bradley PowerFlex 750-series?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Allen-Bradley PowerFlex 750-series?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.
- How tight should the M5 screw on Allen-Bradley PowerFlex 750-series be?
- The source gives 2.8 Nm for ten M5 screws hold the full cabinet options bay guard on frames 8-9, torque 2.8 Nm, 8mm hex.