Dinkle DK2.5 DIN-rail terminal block screw size
M3 · length not stated in the sources
The screws used on Dinkle DK2.5 DIN-rail terminal block are M3. None of the sources we found gives an exact length, so measure the original before you order.
Where it is used: M3 screw-clamp terminal, 600V/25A control-panel wiring.
This entry is marked confirmed and comes from global-ic.de.
For reference, M3 is 3 mm across the threads at 0.5 mm pitch. The imperial size people confuse it with: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.
Dinkle DK2.5 DIN-rail terminal block screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M3 | not stated | 0.5 mm | not stated | not stated | M3 screw-clamp terminal, 600V/25A control-panel wiring | Confirmed |
Fitment records and sources
M3 screw-clamp terminal, 600V/25A control-panel wiring
pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10
How to check the screw before you buy
- On vehicles and bikes, use the original strength class and finish; outdoor hardware is usually stainless or coated to resist corrosion.
- Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M3
- DIN-rail terminal blocks are near-universally M3 across Dinkle, TE, Omron and RND, but torque differs (0.5-0.8 Nm) — over-torquing an M3 terminal screw strips it instantly.
- Terminal-block clamp screws have manufacturer-specific torque values — over-tightening cracks the block or crushes the wire.
More in Vehicles, Marine & Mobility
ABB Terra DC Wallbox (3-phase UL)Adjustable Picatinny rail threaded insertAdult e-scootersAftermarket car stereo cageAirgun scope/rail mount replacement screwsAlpine Head UnitsAnalogis phono cartridge screw setArduino UNO / full-size Arduino boardsAudio MusiKraft cartridge mounting screw kitAudio MusiKraft cartridge/headshell mounting kitBar-end plug or bar-end shifterBerkel 330M Slicer carriage/guard fastener
Browse all 171 in Vehicles, Marine & Mobility →The same screw also fits
Devices whose records share a thread with Dinkle DK2.5 DIN-rail terminal block, closest length match first.
- Wago 869-133 terminal strip also M3
- Camper/caravan/tent fitting screw also M3
- Dinkle DK4N DIN-rail terminal block also M3
- NovAtel OEM7720 heat spreader accessory (01020014) also M3
- Bike computer out-front mount also M3
- Tyco/Advanced MX1 fire panel loop card kit (FP0950) also M3
- Arduino UNO / full-size Arduino boards also M3
- Dinkle DK4 DIN rail terminal block also M3
Questions about Dinkle DK2.5 DIN-rail terminal block screws
- What size screw does Dinkle DK2.5 DIN-rail terminal block use?
- M3 for M3 screw-clamp terminal, 600V/25A control-panel wiring.
- How long are the screws in Dinkle DK2.5 DIN-rail terminal block?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M3 screw?
- 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
- What screwdriver do I need for Dinkle DK2.5 DIN-rail terminal block?
- The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
- Can I use an imperial screw instead of M3?
- No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.