Ducati Monster 1100 Evo screw size
M6 · 18 mm long
If you are replacing a screw on Ducati Monster 1100 Evo, the thread is M6, 18 mm long.
It is listed for TBEIF screw for the license plate holder.
This entry is marked confirmed and comes from stein-dinse.com.
M6 means a 6 mm nominal diameter with a 1 mm thread pitch. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Ducati Monster 1100 Evo screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 18 mm | 1 mm | not stated | not stated | TBEIF screw for the license plate holder | Confirmed |
Fitment records and sources
TBEIF screw for the license plate holder.
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- On vehicles and bikes, use the original strength class and finish; outdoor hardware is usually stainless or coated to resist corrosion.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 18 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- Trailer license plate mounts frequently use 1/4 inch screws in the US, but international and many modern bracket kits have shifted to M6.
More in Vehicles, Marine & Mobility
ABB Terra DC Wallbox (3-phase UL)Adjustable Picatinny rail threaded insertAdult e-scootersAftermarket car stereo cageAirgun scope/rail mount replacement screwsAlpine Head UnitsAnalogis phono cartridge screw setArduino UNO / full-size Arduino boardsAudio MusiKraft cartridge mounting screw kitAudio MusiKraft cartridge/headshell mounting kitBar-end plug or bar-end shifterBerkel 330M Slicer carriage/guard fastener
Browse all 171 in Vehicles, Marine & Mobility →The same screw also fits
Devices whose records share a thread with Ducati Monster 1100 Evo, closest length match first.
- Motorcycle brake disc rotor bolts also M6 × 18 mm
- Gas grill control panel also M6 × 18 mm
- Car dashboard and cluster bezel also M6 × 18 mm
- Shimano BR-M6100 disc brake caliper also M6 × 18 mm
- Small boat deck hardware also M6 × 18 mm
- Motorcycle fairing panels also M6 × 18 mm
- Car license plate mounting screws also M6 × 18 mm
- Shimano Deore BR-M6100 disc brake caliper also M6 × 18 mm
Questions about Ducati Monster 1100 Evo screws
- What size screw does Ducati Monster 1100 Evo use?
- M6 × 18 mm for TBEIF screw for the license plate holder.
- How long are the screws in Ducati Monster 1100 Evo?
- The record gives 18 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Ducati Monster 1100 Evo?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.