Gas grill control panel screw size
M6 · 10 to 20 mm long
The screws used on Gas grill control panel are M6 in lengths from 10 to 20 mm.
It is listed for control panel and igniter bezel on the cart.
This entry is marked reported and comes from webergrills.com.
M6 means a 6 mm nominal diameter with a 1 mm thread pitch. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Gas grill control panel screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 10–20 mm | 1 mm | not stated | not stated | control panel and igniter bezel on the cart | Reported |
Fitment records and sources
control panel and igniter bezel on the cart
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- On vehicles and bikes, use the original strength class and finish; outdoor hardware is usually stainless or coated to resist corrosion.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 10–20 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M6 x 16mm Black Wafer Head Rack Screws for Rittal DK 7094.100 / 7094.110 / 7094.140 19-inch Rack – 20-Pack Replacement
$8.99Choose size -
M6 x 16mm Black Wafer Head Awning & Box Screws for Thule Awning 326 / 327 / 328, Conduit Box 317 & Xpedition 820 / 821 (50333) – 8-Pack Replacement
$6.99Choose size
More in Vehicles, Marine & Mobility
ABB Terra DC Wallbox (3-phase UL)Adjustable Picatinny rail threaded insertAdult e-scootersAftermarket car stereo cageAirgun scope/rail mount replacement screwsAlpine Head UnitsAnalogis phono cartridge screw setArduino UNO / full-size Arduino boardsAudio MusiKraft cartridge mounting screw kitAudio MusiKraft cartridge/headshell mounting kitBar-end plug or bar-end shifterBerkel 330M Slicer carriage/guard fastener
Browse all 171 in Vehicles, Marine & Mobility →The same screw also fits
Devices whose records share a thread with Gas grill control panel, closest length match first.
- Table / mitre saw fence and rails also M6 × 20 mm
- Motorcycle brake disc rotor bolts also M6 × 15–20 mm
- Ducati Monster 1100 Evo also M6 × 18 mm
- Dashcam suction mount ball joint (large) also M6 × 10 mm
- Car dashboard and cluster bezel also M6 × 12–20 mm
- E-bike accessory battery box wheels also M6 × 14 mm
- Lekkie 5mm motor spacer for Bafang BBSHD/BBS02 also M6 × 16 mm
- Adult e-scooters also M6 × 20 mm
Questions about Gas grill control panel screws
- What size screw does Gas grill control panel use?
- M6 × 10–20 mm for control panel and igniter bezel on the cart.
- How long are the screws in Gas grill control panel?
- The records range from 10 to 20 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Gas grill control panel?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.