E-bike accessory battery box wheels screw size
M6 · 14 mm long
The screws used on E-bike accessory battery box wheels are M6, 14 mm long.
It is listed for hexagon Phillips M6x14 screws for wheel mounting.
Head and drive, as the source states them: Phillips drive.
This entry is marked confirmed and comes from akkudoktor.net.
An M6 screw is 6 mm in diameter with a 1 mm pitch, tapped with a 5 mm drill; imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
E-bike accessory battery box wheels screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 14 mm | 1 mm | not stated | Phillips | Hexagon Phillips M6x14 screws for wheel mounting | Confirmed |
Fitment records and sources
Hexagon Phillips M6x14 screws for wheel mounting
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- On vehicles and bikes, use the original strength class and finish; outdoor hardware is usually stainless or coated to resist corrosion.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 14 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Phillips drive. For comparison, standard M6 heads take PH3 (Phillips) or T30 (Torx), or a 5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- Mic stand threads (5/8-27) and tripod threads (1/4-20, 3/8-16) are imperial, not metric — only accessory clips like Gravity's M6 adapter are genuinely M6.
More in Vehicles, Marine & Mobility
ABB Terra DC Wallbox (3-phase UL)Adjustable Picatinny rail threaded insertAdult e-scootersAftermarket car stereo cageAirgun scope/rail mount replacement screwsAlpine Head UnitsAnalogis phono cartridge screw setArduino UNO / full-size Arduino boardsAudio MusiKraft cartridge mounting screw kitAudio MusiKraft cartridge/headshell mounting kitBar-end plug or bar-end shifterBerkel 330M Slicer carriage/guard fastener
Browse all 171 in Vehicles, Marine & Mobility →The same screw also fits
Devices whose records share a thread with E-bike accessory battery box wheels, closest length match first.
- Gas grill control panel also M6 × 14 mm
- Car dashboard and cluster bezel also M6 × 14 mm
- Motorcycle side panels and tail cowl also M6 × 14 mm
- Motorcycle fairing panels also M6 × 14 mm
- Car license plate U-clip retaining fasteners (trim) also M6 × 14 mm
- Large soundbars & subwoofers also M6 × 14 mm
- VESA MIS-F display mount (200x200 and larger) also M6 × 14 mm
- Universal full-motion TV mount kits also M6 × 14 mm
Questions about E-bike accessory battery box wheels screws
- What size screw does E-bike accessory battery box wheels use?
- M6 × 14 mm for hexagon Phillips M6x14 screws for wheel mounting.
- How long are the screws in E-bike accessory battery box wheels?
- The record gives 14 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for E-bike accessory battery box wheels?
- The source lists a Phillips drive. Standard M6 heads otherwise take PH3 (Phillips) or T30 (Torx), or a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.