Eberspacher Hydronic D4WSC / D5WS heater screw size
M5 · 25 mm long
If you are replacing a screw on Eberspacher Hydronic D4WSC / D5WS heater, the thread is M5, 25 mm long.
Where it is used: blower motor cover and intake hood screw M5 x 25 mm.
This entry is marked confirmed and comes from krueger.co.uk.
For reference, M5 is 5 mm across the threads at 0.8 mm pitch. The imperial size people confuse it with: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Eberspacher Hydronic D4WSC / D5WS heater screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 25 mm | 0.8 mm | not stated | not stated | Blower motor cover and intake hood screw M5 x 25 mm | Confirmed |
Fitment records and sources
Blower motor cover and intake hood screw M5 x 25 mm
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- Appliance panels often use self-tapping screws into sheet metal or plastic, and machine screws into nuts or inserts — keep each type where it came from.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 25 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- M5 is not a VESA size — it shows up in bikes, furniture and appliances, rarely on displays.
- Some scooters and appliances use self-tapping screws of similar diameter rather than true M5 machine threads.
More in Appliances & HVAC
Appliance door hingesAppliance handlesAstoria/CMA espresso solenoid group head (used in coffee kiosk equipment)Astoria/CMA espresso solenoid group head screwBerkel 330M Slicer cover fastenerBerkel 330M Slicer sharpener/guard mountingBezzera Giulia espresso machineBosch dishwasherCoffee machine control panelDaikin FTXS/CTXS Mini-split control board / cover screwDaikin FTXS/CTXS Mini-split indoor unit mounting / terminal cover screwDaikin FTXS/CTXS Mini-split indoor unit terminal cover / mounting plate screw
Browse all 62 in Appliances & HVAC →The same screw also fits
Devices whose records share a thread with Eberspacher Hydronic D4WSC / D5WS heater, closest length match first.
- Appliance handles also M5 × 25 mm
- DIN 912 socket-head cap screw also M5 × 25 mm
- Voron 2.4 frame corner brackets also M5 × 25 mm
- DIN 965 / ISO 7046 countersunk Phillips screw also M5 × 25 mm
- Hospital bed siderail and actuator brackets also M5 × 25 mm
- OpenBuilds C-Beam Machine also M5 × 25 mm
- Home safe hinge and strike bolts also M5 × 25 mm
- ASUS PG32UCDM also M5 × 25 mm
Questions about Eberspacher Hydronic D4WSC / D5WS heater screws
- What size screw does Eberspacher Hydronic D4WSC / D5WS heater use?
- M5 × 25 mm for blower motor cover and intake hood screw M5 x 25 mm.
- How long are the screws in Eberspacher Hydronic D4WSC / D5WS heater?
- The record gives 25 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Eberspacher Hydronic D4WSC / D5WS heater?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.