ASUS PG32UCDM screw size
M4 / M5 · 10 to 25 mm long
Our records put ASUS PG32UCDM on M4 and M5 screws in lengths from 10 to 25 mm.
There are 2 separate fitment records for it, including vesa mount (M4) and stand (M5).
2 of the 2 records are marked confirmed, drawn from 1 source (dlcdnets.asus.com).
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
ASUS PG32UCDM screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 10 mm | 0.7 mm | not stated | not stated | Vesa mount | Confirmed |
| M5 | 25 mm | 0.8 mm | not stated | not stated | Stand | Confirmed |
Fitment records and sources
Vesa mount
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
Stand
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). This device also uses M5, so measure each screw rather than assuming they match.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 10–25 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4 / M5
- Dashcam mounts advertised as '1/4" M4 screw joint' have two different threads: the 1/4"-20 camera thread and a separate M4 grub screw for the ball joint — don't order the wrong one.
- VESA fixes the hole pattern and max thread depth, not screw length — length depends on the panel back and any spacers.
- M5 is not a VESA size — it shows up in bikes, furniture and appliances, rarely on displays.
- The 'GoPro thread' is M5-0.8, a de facto standard on third-party mounts, and is not the imperial 1/4-20 tripod thread.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Displays, TVs & Mounts
The same screw also fits
Devices whose records share a thread with ASUS PG32UCDM, closest length match first.
- Dell U2518D also M4 × 10 mm
- Dell P2421D also M4 × 10 mm
- ASUS VG259QMY also M4 × 10 mm
- Dell U2515H also M4 × 10 mm
- Dell U2417HA also M4 × 10 mm
- Samsung range / wall oven also M4 × 10 mm
- Dell P1917S also M4 × 10 mm
- LG 43LJ5000 also M4 × 10 mm
Questions about ASUS PG32UCDM screws
- What size screw does ASUS PG32UCDM use?
- M4 × 10 mm for vesa mount; M5 × 25 mm for stand.
- How long are the screws in ASUS PG32UCDM?
- The records range from 10 to 25 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for ASUS PG32UCDM?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.