Elo self-service kiosk stand base screw (Bag A/B) screw size
M4 · 8 mm long
The screws used on Elo self-service kiosk stand base screw (Bag A/B) are M4, 8 mm long.
Where it is used: pan-head and flat-head M4X8 variants.
Head and drive, as the source states them: flat / countersunk head.
This entry is marked confirmed and comes from docs.elotouch.com.
For reference, M4 is 4 mm across the threads at 0.7 mm pitch. The imperial size people confuse it with: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Elo self-service kiosk stand base screw (Bag A/B) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 8 mm | 0.7 mm | Flat / countersunk | not stated | Pan-head and flat-head M4X8 variants | Confirmed |
Fitment records and sources
Pan-head and flat-head M4X8 variants
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Printers and POS terminals often use self-tapping screws into plastic; re-use the original thread path instead of cutting a new one.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: the source describes a countersunk (flat) head, and those are measured overall, from the top of the head to the tip.
- The record states 8 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- M4 and 6-32 UNC share a nominal diameter with different pitch — a classic cross-thread in US-market kits.
More in Printers, POS & Office
Arca-Swiss / GoPro DIY adaptersBixolon SRP-B300II POS receipt printerBrother DCP-8110D laser printerBrother HL-2170W laser printerBrother MFC-8950DW laser printerCoin validator / hopper front plateCoin-door / vending coin mech holder thumb screwCOSEL power supply terminal blockDiebold Nixdorf ATM (PN 49221808000F-26)Diebold Nixdorf DN100 ATMDiebold Nixdorf DN100 nylon screwDiebold Opteva ATM cassette screw
Browse all 58 in Printers, POS & Office →The same screw also fits
Devices whose records share a thread with Elo self-service kiosk stand base screw (Bag A/B), closest length match first.
- Epson SC-P8500D / T7700D large-format printer also M4 × 8 mm
- Elo self-service kiosk stand (15-22in floor-top) also M4 × 8 mm
- Ingenico Lane 3000 PIN pad metal adaptor screw also M4 × 8 mm
- HP Color LaserJet 8500 2000-sheet input unit also M4 × 8 mm
- Coin-door / vending coin mech holder thumb screw also M4 × 8 mm
- Diebold Opteva ATM cassette screw also M4 × 8 mm
- Elo self-service kiosk countertop stand (E421137) also M4 × 8 mm
- Elo Slim self-service stand also M4 × 8 mm
Questions about Elo self-service kiosk stand base screw (Bag A/B) screws
- What size screw does Elo self-service kiosk stand base screw (Bag A/B) use?
- M4 × 8 mm for pan-head and flat-head M4X8 variants.
- How long are the screws in Elo self-service kiosk stand base screw (Bag A/B)?
- The record gives 8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Elo self-service kiosk stand base screw (Bag A/B)?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.