Ingenico Lane 3000 PIN pad metal adaptor screw screw size
M4 · 8 mm long
Our records put Ingenico Lane 3000 PIN pad metal adaptor screw on M4 screws, 8 mm long.
It is listed for M4x8 pan head.
Head and drive, as the source states them: pan head.
This entry is marked confirmed and comes from onlinehelp.ncrvoyix.com.
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Ingenico Lane 3000 PIN pad metal adaptor screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 8 mm | 0.7 mm | Pan head | not stated | M4x8 pan head | Confirmed |
Fitment records and sources
How to check the screw before you buy
- Check whether the mount uses a VESA pattern or a vendor bracket before buying screws.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for pan head screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The record states 8 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- M4 and 6-32 UNC share a nominal diameter with different pitch — a classic cross-thread in US-market kits.
More in Printers, POS & Office
Arca-Swiss / GoPro DIY adaptersBixolon SRP-B300II POS receipt printerBrother DCP-8110D laser printerBrother HL-2170W laser printerBrother MFC-8950DW laser printerCoin validator / hopper front plateCoin-door / vending coin mech holder thumb screwCOSEL power supply terminal blockDiebold Nixdorf ATM (PN 49221808000F-26)Diebold Nixdorf DN100 ATMDiebold Nixdorf DN100 nylon screwDiebold Opteva ATM cassette screw
Browse all 58 in Printers, POS & Office →The same screw also fits
Devices whose records share a thread with Ingenico Lane 3000 PIN pad metal adaptor screw, closest length match first.
- Elo self-service kiosk stand (15-22in floor-top) also M4 × 8 mm
- Elo self-service kiosk stand base screw (Bag A/B) also M4 × 8 mm
- Epson SC-P8500D / T7700D large-format printer also M4 × 8 mm
- Elo self-service kiosk countertop stand (E421137) also M4 × 8 mm
- Elo Slim self-service stand also M4 × 8 mm
- Elo Slim self-service stand screw (Bag I) also M4 × 8 mm
- HP Color LaserJet 8500 2000-sheet input unit also M4 × 8 mm
- Diebold Opteva ATM cassette screw also M4 × 8 mm
Questions about Ingenico Lane 3000 PIN pad metal adaptor screw screws
- What size screw does Ingenico Lane 3000 PIN pad metal adaptor screw use?
- M4 × 8 mm for M4x8 pan head.
- How long are the screws in Ingenico Lane 3000 PIN pad metal adaptor screw?
- The record gives 8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Ingenico Lane 3000 PIN pad metal adaptor screw?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.