What size screw does Elo self-service kiosk stand pan-head screw (Bag C) use?

M3 × 8 mm for BOM: SCREW, M3X8, PAN-HEAD, CROSS-RECESS.

How long are the screws in Elo self-service kiosk stand pan-head screw (Bag C)?

The record gives 8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.

What is the thread pitch of an M3 screw?

0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.

What screwdriver do I need for Elo self-service kiosk stand pan-head screw (Bag C)?

The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.

Can I use an imperial screw instead of M3?

No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Elo self-service kiosk stand pan-head screw (Bag C)?

TechSpareWarehouse (our own store) lists M3 x 8mm, which matches the length in the records above.

Elo self-service kiosk stand pan-head screw (Bag C) screw size

M3 · 8 mm long

The screws used on Elo self-service kiosk stand pan-head screw (Bag C) are M3, 8 mm long.

The record covers BOM: SCREW, M3X8, PAN-HEAD, CROSS-RECESS.

Head and drive, as the source states them: pan head.

This entry is marked confirmed and comes from docs.elotouch.com.

M3 means a 3 mm nominal diameter with a 0.5 mm thread pitch. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.

Elo self-service kiosk stand pan-head screw (Bag C) screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M3	8 mm	0.5 mm	Pan head	not stated	BOM: SCREW, M3X8, PAN-HEAD, CROSS-RECESS	Confirmed

Fitment records and sources

M38.0mmconfirmed

BOM: SCREW, M3X8, PAN-HEAD, CROSS-RECESS

pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10

Source

How to check the screw before you buy

Printers and POS terminals often use self-tapping screws into plastic; re-use the original thread path instead of cutting a new one.
Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: for pan head screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
The record states 8 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M3

M3 (3.0mm, 0.5mm pitch) is not #6-32 UNC (~3.5mm) — they look identical and cross-thread, the single most common PC-building mistake.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Printers, POS & Office

Arca-Swiss / GoPro DIY adapters Bixolon SRP-B300II POS receipt printer Brother DCP-8110D laser printer Brother HL-2170W laser printer Brother MFC-8950DW laser printer Coin validator / hopper front plate Coin-door / vending coin mech holder thumb screw COSEL power supply terminal block Diebold Nixdorf ATM (PN 49221808000F-26)Diebold Nixdorf DN100 ATM Diebold Nixdorf DN100 nylon screw Diebold Opteva ATM cassette screw

Browse all 58 in Printers, POS & Office →

The same screw also fits

Devices whose records share a thread with Elo self-service kiosk stand pan-head screw (Bag C), closest length match first.

Brother HL-2170W laser printer also M3 × 8 mm
Bixolon SRP-B300II POS receipt printer also M3 × 8 mm
HP LaserJet 9000/9040/9050 series printer also M3 × 8 mm
Elo floor-mount self-service stand screw also M3 × 8 mm
Epson SC-P8500D / T7700D large-format printer also M3 × 8 mm
Elo countertop self-service stand screw also M3 × 8 mm
Diebold Nixdorf DN100 ATM also M3 × 8 mm
Elo self-service kiosk stand, strap screws also M3 × 8 mm

Questions about Elo self-service kiosk stand pan-head screw (Bag C) screws

What size screw does Elo self-service kiosk stand pan-head screw (Bag C) use?: M3 × 8 mm for BOM: SCREW, M3X8, PAN-HEAD, CROSS-RECESS.
How long are the screws in Elo self-service kiosk stand pan-head screw (Bag C)?: The record gives 8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
What is the thread pitch of an M3 screw?: 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
What screwdriver do I need for Elo self-service kiosk stand pan-head screw (Bag C)?: The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
Can I use an imperial screw instead of M3?: No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Elo self-service kiosk stand pan-head screw (Bag C)?: TechSpareWarehouse (our own store) lists M3 x 8mm, which matches the length in the records above.

Heads up: shipping delay