Elo touch display/signage panel (dimensional drawing MS602782) screw size
M4 · 6 mm long
Our records put Elo touch display/signage panel (dimensional drawing MS602782) on M4 screws, 6 mm long.
It is listed for VESA mount threads, x8, max thread engagement depth 6mm.
This entry is marked confirmed and comes from docs.elotouch.com.
For reference, M4 is 4 mm across the threads at 0.7 mm pitch. The imperial size people confuse it with: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Elo touch display/signage panel (dimensional drawing MS602782) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 6 mm | 0.7 mm | not stated | not stated | VESA mount threads, x8, max thread engagement depth 6mm | Confirmed |
Fitment records and sources
VESA mount threads, x8, max thread engagement depth 6mm
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 6 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Display mounts mix systems: the screen side is metric M4/M6, but the wall side of many mounts uses imperial wood screws such as #14 x 2.5in.
- VESA fixes the hole pattern and max thread depth, not screw length — length depends on the panel back and any spacers.
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with Elo touch display/signage panel (dimensional drawing MS602782), closest length match first.
- VESA MIS-B displays (4-7.9 inch) also M4 × 6 mm
- VESA FDMI Part B and C display mounts also M4 × 6 mm
- Elo Z20 POS stand Gen2 (E378179) also M4 × 6 mm
- LED video wall cabinet, frame-to-link bracket (SCREW B) also M4 × 6 mm
- GCX 75/100mm VESA flush display mount also M4 × 6 mm
- LED video wall cabinet headless bolt E also M4 × 6 mm
- Elo Pay 15.6-inch Tap-to-Pay POS terminal, VESA mount also M4 × 6 mm
- Portable 13-15in travel monitors also M4 × 6 mm
Questions about Elo touch display/signage panel (dimensional drawing MS602782) screws
- What size screw does Elo touch display/signage panel (dimensional drawing MS602782) use?
- M4 × 6 mm for VESA mount threads, x8, max thread engagement depth 6mm.
- How long are the screws in Elo touch display/signage panel (dimensional drawing MS602782)?
- The record gives 6 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Elo touch display/signage panel (dimensional drawing MS602782)?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.